CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   FLUENT (http://www.cfd-online.com/Forums/fluent/)
-   -   Error: CDR: invalid argument [1]: wrong type [not a pair];Error Object: #f (http://www.cfd-online.com/Forums/fluent/67939-error-cdr-invalid-argument-1-wrong-type-not-pair-error-object-f.html)

Perseu September 1, 2009 08:28

Error: CDR: invalid argument [1]: wrong type [not a pair];Error Object: #f
 
Hi,

I have used the Fluent for simulation of wave generation in a tank (piston wave maker), but I have a problem when use a function "autosave". During the simulation, with many iterations (more 80.000), I saved the case and data through function autosave. However, when lack the electricity or when I cancel for a time and close the program for to begin again, occur the error:

Error: CDR: invalid argument [1]: wrong type [not a pair]
Error Object: #f

Please, someone can help me?

Thanks

Perseu

mpa June 7, 2010 02:39

Hi Perseu,
I have the same problem:
cdr: invalid argument [1]: wrong type [not a pair]
Error object: #f

what could it be? Have you found a solution?

thanks

wangguobin14 June 26, 2010 22:17

Error: CAR: invalid argument [1]: wrong type [not a pair]
 
hi ,
have you solved your problem,
what does it mean? how to smooth it?
thank you !
wangguobin@163.com for contact:eek:

sanmysterio June 29, 2010 07:25

Error: CDR: invalid argument [1]: wrong type [not a pair] Error Object: #f
 
hi,
I am also getting the same problem when i run my case in batch mode on cluster but it was running fine with gui
kindly help

yoossie August 27, 2010 05:00

Nobody know how to solve this problem?

Because I'm only writing the events of a Dynamic Mesh, and (following a tutorial, but applied to my study) when I write my sliding interfaces it appears also this error.

I cannot understand, because, I have defined in the same way as the tutorial, I did it also in the same problem but with a different conditions (that they mustn't afect this) and it was no problem.

What can I do? Anyone knows?

Thanks for your replying

freeday September 17, 2010 23:59

So, do I....

Please help me...

fossil September 3, 2011 05:19

i have the same problem:confused:

fox000002 September 3, 2011 13:04

The error message indicates that there is an error in the scheme code.

A list value is needed, but a boolean value "#f" is fed.

You should check your case/data file, find the position and fix it.

zayzan December 30, 2011 03:43

Quote:

Originally Posted by fox000002 (Post 322781)
The error message indicates that there is an error in the scheme code.

A list value is needed, but a boolean value "#f" is fed.

You should check your case/data file, find the position and fix it.


Find the position of what exactly? I don't get it!
Can you explain further please?

Thanks

raghu.tejaswi August 30, 2012 16:03

Is this problem solved???

I had the same problem several times. I save the case (and data sometimes), close it and reopen it. IT works everytime.
Hope someone should try it out..

raghu.tejaswi August 30, 2012 16:05

PS: or try remeshing (can be coarser or finer..), it should work

p.bhushan2727@gmail.com January 10, 2013 13:23

same error
 
dear frnd i am getting same error for my fluent problem any body knw ans plz tell me:mad:

raghu.tejaswi January 10, 2013 14:01

Hi Bhushan,

did you try doing the things I mentioned in the above comment?
Honestly, it worked for me.

raghu

p.bhushan2727@gmail.com January 11, 2013 01:33

hi raghu i have save case and data file done lots of time but i am getting same error i am doing Multiple Rotating Reference Frames problem tried remeshing but not getting .......... i have made interface and for my case is there any problem in that case

raghu.tejaswi January 11, 2013 03:05

Quote:

Originally Posted by p.bhushan2727@gmail.com (Post 401307)
hi raghu i have save case and data file done lots of time but i am getting same error i am doing Multiple Rotating Reference Frames problem tried remeshing but not getting .......... i have made interface and for my case is there any problem in that case

I do not exactly understand the quantum of your problem. The problem can be tricky when interfaces are involved. Make doubly sure your interfaces are perfect. WHen I got this exact error, I just saved this as a different filename in a diff folder and it worked everytime. Thats the reason I am commenting here.
If this does not work, probably you can describe your problem in detail and eithr me or someone else can help you. and pls check if the error you receive is exactly the same as mentioned in this post.

p.bhushan2727@gmail.com January 11, 2013 03:39

darreuis type wind turbine cfd
 
5 Attachment(s)
DEAR raghu ,
i am doing my m.tech project in water turbine cfd with moving sate for that concern i have made my mesh as one paper and for that concern i have made one main rectangular domain in which one circular rotating domain and in that circle another 3 circular domain around the aerofoil shape baldes in that case whole circular domain with 3 inner circle is roatating with some angular velocity i have attaching some images of my mesh with this i have made interfaces for betn main domain-- outer domain , outer domain --3 inner circle ....and i am using for that concern Multiple Rotating Reference Frames for simulations ... its running but case and dat file recall this error ocuur.... and thanx for u r help ...& plz help me for that concern

caitoc July 3, 2013 11:15

Reset the model in workbench
 
Hi all,
I had this problem too during my fluent modelling in ansys workbench.

My solution is simple: reset the "Setup", open the fluent and now you should not encounter this error anymore

sajeesh July 8, 2013 22:37

Hi all

I came across the same problem in VOF simulation when defining the Run calculation_create animation play back file..At that time just save the case and data file and reopen it..It will work fine...This is formed when reassigning more than a data to the same name..Eg contour plots of phases and pressure assign to same file sequence1..Assign each contour plot to each file and these problem wont arise...

This is what i am feeling

Thnx
Sajeesh

Katja May 29, 2014 07:50

Periodicity
 
Hi all,

I received the same error while trying to view periodic repeats of my geometry, so I guess it has something to do with wrongly defining the BCs?

Tank August 26, 2014 02:46

I was receiving the same error message:

I solved this by deleting all my monitors. It also disappeared when I gave each monitor its own window.

So perhaps save your case and delete all your monitors to determine if this is the source of your problem?

Hope this helped!


All times are GMT -4. The time now is 15:26.