CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   FLUENT (http://www.cfd-online.com/Forums/fluent/)
-   -   Diesel Engine combustion chamber analysis (http://www.cfd-online.com/Forums/fluent/71833-diesel-engine-combustion-chamber-analysis.html)

sachinthakre January 17, 2010 03:21

Diesel Engine combustion chamber analysis
 
hello all
I am doing cfd analysis(3D) of diesel engine combustion chamber using Fluent. I have carried out the colds flow simulation. Now I am going for combustion.
Could anybody tell me which combustion model i should use?
Should I use speicies transport or Non-premixed combustion?
Can I get some tips over the volumetric reactions and ignition delay model?
Thanks in advance

herntan January 17, 2010 22:17

I definately u won't get any answer for this post.
Please study more on Fluent simulation and ur own target before u post it.
AND , post it in detail with picture /video.

anyhow, just a piece of advice. good luck.

sachinthakre January 19, 2010 11:42

hi
actually I am doing combustion analysis to study some factors like heat release for the single cylinder diesel engine for which I am having experimental results. I have completed 3D meshing and successfully carried out cold flow simulation for all the strokes with mesh deformation.
Now I am going to carry out combustion. I have gone through fluent user guide. I am getting some error using species transport. Solution is diverging just after diesel injection starts.
if i could get some tips on it.
thanks.

sachinthakre January 26, 2010 10:35

CFD analysis of combustion in Diesel engine using fluent
 
hi
actually I am doing combustion analysis to study some factors like heat release for the single cylinder diesel engine for which I am having experimental results. I have completed 3D meshing and successfully carried out cold flow simulation for all the strokes with mesh deformation.
Now I am going to carry out combustion. I have gone through fluent user guide. I am getting some error using species transport. Solution is diverging just after diesel injection starts.
if i could get some tips on it.
thanks in advance

herntan January 27, 2010 23:08

picture , video ... detail explain... error message screen shot.. ur not really mean to ask question here....so don't give too much hope on getting responce.

mas January 28, 2010 02:19

Quote:

Originally Posted by sachinthakre (Post 243086)
Solution is diverging just after diesel injection starts.

You should try to balance the mesh size(x), the time step size(dt) from the predicted spray velocity(v). In particular, you should focus on especially near the spray inlet where the velocity is the highest. Use this guideline, dt < x/v.

sairam January 28, 2010 13:27

i think u can use non-per mixture because it is specially used for this purpose

keerthi June 3, 2011 07:16

combustion analysis reg...
 
sir, i am starting combustion analysis right now so please can u get me some materials to go through.... my mail id is keerthi_gpet@yahoo.co.in

Sergiu August 25, 2011 05:40

hello sachinthakre,

Can you show me how you did the simulation for cold flow simulation? I realy need this to my doctorate thesis. Please can you send me your model to stroe_sergiu@yahoo.com.
Thank you very much and good lock,
Sergiu

Erny August 25, 2011 11:02

Quote:

Originally Posted by herntan (Post 242866)
I definately u won't get any answer for this post.
Please study more on Fluent simulation and ur own target before u post it.
AND , post it in detail with picture /video.

anyhow, just a piece of advice. good luck.

Just out of curiosity where are you supposed to ask then?

syler3321 October 10, 2011 05:27

Hern Tan is supposed to ask for a grammar check.. spelling too.. dont be a prick. if u have nothing to contribute keep quiet

roukaia November 4, 2011 14:28

need help for meshing in gambit
 
i need to simulate an IC engine 2D (lister petter) so i tried to reproduce the same geometry as the tutoriel in-cylinder mesh
now i have no idea about how to construct the mesh (structured and non structured mesh in one face) in the valve
i need the valve layering zones to in structered (quad) because o the layering
have you got any idea how to do it in gambit

dipak patel August 13, 2013 14:14

hi... i have a confusion about selection of combustion chamber for cfd analysis in ci engine so can you give one of combustion chamber which is recently used in vehicle .........


All times are GMT -4. The time now is 17:18.