|
[Sponsors] |
January 21, 2010, 12:02 |
Gambit export file not created
|
#1 |
New Member
Amit Verma
Join Date: Jan 2010
Posts: 6
Rep Power: 16 |
Hi Everybody,
I am making a mesh for a laminar flow problem through a pipe. So I created 4 vertices>>edges>face and finally I made a mesh. then I specified boundry types. After that I saved the file. But when I try to export to it gives the following error and warning. "WARN: Boundry Entity Centerline does not contain any valid entry and is not written. No Entities were found for mesh export. Error were found during export. Export file was not created. " However the centerline is edge 4 of my mesh and I have done a valid entry. Kindly help in this regard. Amit |
|
January 21, 2010, 12:31 |
|
#2 |
New Member
Join Date: Dec 2009
Location: Germany
Posts: 6
Rep Power: 16 |
You have to specify create a 3D or 2D mesh and in your case 2D?
I think there is in the mesh export window a small button... |
|
January 21, 2010, 13:16 |
|
#3 |
New Member
Amit Verma
Join Date: Jan 2010
Posts: 6
Rep Power: 16 |
Sorry ...I didnt wrote about it....
Yes I had clicked 2d...while exporting.....but still.. the problems remain!! |
|
January 21, 2010, 13:20 |
|
#4 |
New Member
Join Date: Dec 2009
Location: Germany
Posts: 6
Rep Power: 16 |
okay, 2d
have you the right directions, I think in 2d you have to use x and y? |
|
January 22, 2010, 02:59 |
|
#5 |
Senior Member
YH Tan
Join Date: Mar 2009
Location: Malaysia
Posts: 119
Rep Power: 17 |
How about u post up a screen shot of ur Gambit mesh and error message.
__________________
Herntan, Add Reputation if I am right |
|
January 22, 2010, 05:58 |
|
#6 |
New Member
Amit Verma
Join Date: Jan 2010
Posts: 6
Rep Power: 16 |
Here is the screen short of transcript window!!!
|
|
January 22, 2010, 06:10 |
|
#7 |
Senior Member
YH Tan
Join Date: Mar 2009
Location: Malaysia
Posts: 119
Rep Power: 17 |
Ur mesh is wrong.
U cannot just mesh the edge, u need to mesh the whole surface. Ur running on 2D simulation right?
__________________
Herntan, Add Reputation if I am right |
|
January 22, 2010, 06:46 |
|
#8 |
New Member
Amit Verma
Join Date: Jan 2010
Posts: 6
Rep Power: 16 |
Thanks....I meshed the face as well..... and then it worked.... thanks again!!!
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Working directory via command line | Luiz | CFX | 4 | March 6, 2011 20:02 |
cannot export mesh file from Gambit | kenya0514 | Main CFD Forum | 1 | January 18, 2010 00:12 |
Version 15 on Mac OS X | gschaider | OpenFOAM Installation | 113 | December 2, 2009 10:23 |
Compiling OpenFOAM13 on AMD64 with Redhat Enterprise | mbeaudoin | OpenFOAM Installation | 20 | June 17, 2008 06:43 |
GAMBIT: Export values of an Array into a file | Marcus | FLUENT | 0 | January 4, 2007 08:23 |