 |
 |
 |
|
|
|
[Sponsors] | ||||
April 21, 2011, 08:13
|
Drawing Contours without showing mesh
|
#1 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15  |
I would like to know if it is possible for me to draw contours in FLUENT while the mesh does not show
Thank you |
|
|
|
|
|
April 21, 2011, 13:43
|
draw grid
|
#2 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
you can disable the draw grid in display panel in fluent
|
|
|
|
|
|
|
May 16, 2011, 14:37
|
|
#3 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15 |
thank you for your reply. Yes, it works, but when I have drawn my contour or vector and remove the mesh it shows an empty box.
Can you please give me the exact procedure to draw a contour without the mesh showing. what I clicked; Display > Mesh > Display I have attached the pictures to show what I mean |
|
|
|
|
|
|
May 17, 2011, 06:53
|
|
#4 |
|
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
diplay/contour
__________________
In memory of my friend Hervé: CFD engineer & freerider  |
|
|
|
|
|
|
May 17, 2011, 06:58
|
|
#5 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
I do this work and do not have this problem...
please explain |
|
|
|
|
|
|
May 17, 2011, 07:14
|
|
#6 |
|
New Member
Join Date: May 2011
Posts: 2
Rep Power: 0 |
display/contours/temperature or velocity oir whatever
and desable "Draw grid" |
|
|
|
|
|
|
May 17, 2011, 08:15
|
|
#7 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
your case is 2d, so you should not select any surface to display contour.
I send two picture for you. see these pictures and follow them.   
|
|
|
|
|
|
|
May 18, 2011, 12:05
|
|
#8 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15 |
Thanks for your reply, could you please post the pictures again because I cant find them
|
|
|
|
|
|
|
May 18, 2011, 12:20
|
|
#9 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15 |
mojtaba1365 and ioc,
I did uncheck the draw mesh box, but it still displays the mesh. Check it in this pdf I would attach |
|
|
|
|
|
|
May 18, 2011, 16:00
|
|
#10 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
I got it.
follow this: display-contour-do not select any surface in surface panel- select Filed. you have selected all the surfaces, but you should not do this work be my guest buddy... |
|
|
|
|
|
|
May 18, 2011, 16:21
|
|
#11 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15 |
Brilliant. Thank you, that works. Do you know if/how I can apply law of the wall in FLUENT.
|
|
|
|
|
|
|
May 18, 2011, 16:32
|
|
#12 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
please explain...
|
|
|
|
|
|
|
May 18, 2011, 16:47
|
|
#13 |
|
New Member
Tolu Openiyi
Join Date: Nov 2010
Posts: 18
Rep Power: 15 |
I was asked to apply law of the wall http://en.wikipedia.org/wiki/Law_of_the_wall to my cylinder wall, dont know whether FLUENT does this.
|
|
|
|
|
|
|
May 18, 2011, 16:54
|
|
#14 |
|
New Member
mojtaba
Join Date: Nov 2010
Posts: 25
Rep Power: 15 |
you can run your case and then compare your results with the law of the wall formula...
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| [ICEM] surface mesh merging problem | everest | ANSYS Meshing & Geometry | 44 | April 14, 2016 06:41 |
| [snappyHexMesh] snappyHexMesh won't work - zeros everywhere! | sc298 | OpenFOAM Meshing & Mesh Conversion | 2 | March 27, 2011 21:11 |
| 2d irregular grid | Remy | Main CFD Forum | 1 | December 22, 2008 04:49 |
| basic of mesh refinement | arya | CFX | 4 | June 19, 2007 12:21 |
| Mesh Refinement | JY | Siemens | 7 | September 19, 2002 13:37 |
7Likes
Linear Mode
