|
[Sponsors] |
May 15, 2006, 12:51 |
3D mesh around a wing using gambit
|
#1 |
Guest
Posts: n/a
|
I am using Gambit for creating 3Dmesh round a wing , I need a help for creating this mesh . I tried to mesh edges, faces and then volumes. This method worked for volumes which does not contain wing. for the volume which contains wing this method fails...Why???!!!
Can any one send me a steps or advise? Greast Thanks |
|
May 15, 2006, 14:55 |
Re: 3D mesh around a wing using gambit
|
#2 |
Guest
Posts: n/a
|
There is a gambit tutorial for meshing an airplane geometry (half section). Maybe that will help you.
|
|
May 16, 2006, 03:06 |
Re: 3D mesh around a wing using gambit
|
#3 |
Guest
Posts: n/a
|
where is the tutorial file?In the standard gambit help file, I cann't find any tutorial file about meshing an airplane. could you sent this file to my email:dongtaomail@gmail.com, thanks in advance.
|
|
May 16, 2006, 14:44 |
Re: 3D mesh around a wing using gambit
|
#4 |
Guest
Posts: n/a
|
||
May 17, 2006, 12:42 |
Re: 3D mesh around a wing using gambit
|
#5 |
Guest
Posts: n/a
|
Thanks Anindya,,, This will help me
M. Essuri |
|
May 25, 2006, 03:44 |
Re: 3D mesh around a wing using gambit
|
#6 |
Guest
Posts: n/a
|
you can use triangle to mesh all the face of volume.Note:divide many vertices on leading edge and trailing edge of the wing.then, you can use Tgrid to smooth the mesh.You can email to me ro have more info.I am going to graduate from Univesity and my thesis is "Flow over an 3D airfoil using gambit and fluent..""
|
|
June 6, 2006, 11:38 |
Re: 3D mesh around a wing using gambit
|
#7 |
Guest
Posts: n/a
|
Dear aerosapce_iist@yahoo.com, I can't email to u. You can mesh your foil in gambit and then u use fluent, set the condition in fluent e.g. define model(solver,viscous,..).In gambit, u set the bounary condition for faces(velocity inlet, pressure outlet, symetry, ..) to set the value of boundary condition to solve...The residual u use in Fluent is about 1e-5. after about 2500 iteration, the solution converges anh u will have the pressure.I send u apic of wing that I have done.hope that I will help u.
|
|
June 6, 2006, 11:39 |
aerosapce_iist *NM*
|
#8 |
Guest
Posts: n/a
|
|
|
April 30, 2009, 15:05 |
|
#9 | |
New Member
Kartik
Join Date: Apr 2009
Posts: 4
Rep Power: 16 |
Quote:
Hi i would be glad to see you work. i am looking to work on same lines. my email id is kkadakia2009@gmail.com regards kartik |
||
April 30, 2009, 16:06 |
Hii
|
#10 |
Member
ANIL
Join Date: Apr 2009
Posts: 35
Rep Power: 16 |
@@: QuynhGiao
Guest I am working on" Flow over 3d wing with sinusoidal leading edge", but i coudnt get a good volume mesh in Gambit because of sharp trailing edge... In next attemp, i joined the last two points of airfoil with straight line, but the 3d Boundary layer resulted in highly skewed elements. I wud be glad to see your work, it might help me...looking forward to hear from you. email: anilsmailaero@gmail.com Thank you. |
|
July 21, 2010, 03:04 |
|
#11 |
Member
Join Date: Jul 2009
Posts: 70
Rep Power: 16 |
Hello Quynh Giao,
Today, I've just found your post here. It was posted over 4 years ago. However I hope you still work with CFD now! ^_^. Therefore, I would ask your email to discuss with you about this topic. Thanks you so much! Nguyen Van Trieu. Email: trieuckgt@gmail.com |
|
February 9, 2012, 17:49 |
|
#12 |
New Member
Amr Ahmed Ahmed El feky
Join Date: Jan 2012
Posts: 1
Rep Power: 0 |
Sorry i have the same problem . I am using Gambit for creating 3Dmesh round a wing , I need a help for creating this mesh . I tried to mesh edges, faces and then volumes. This method worked for volumes which does not contain wing. for the volume which contains wing this method fails..
The link of tutorial http://www.wka.tu-harburg.de/intra/d...............is not working |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Converting Fluent mesh files to Gambit neutral files | samuelkc | ANSYS Meshing & Geometry | 9 | April 21, 2021 07:28 |
[ICEM] Structured Mesh 3D Wing Tip | Michiel | ANSYS Meshing & Geometry | 5 | October 21, 2010 09:39 |
fluent add additional zones for the mesh file | SSL | FLUENT | 2 | January 26, 2008 12:55 |
Mesh Resolution in Gambit | Vidya Raja | FLUENT | 2 | January 19, 2006 00:35 |
3-D Mesh Check in Gambit..... | SHR | FLUENT | 4 | March 25, 2003 04:10 |