FLUENT received fatal signal (ACCESS_VIOLATION)

osamaghani · March 28, 2012, 00:49

Hello!
I am getting this error whenever I read the MESH in fluent.

"FLUENT received fatal signal (ACCESS_VIOLATION)"

I am using ICEM to create mesh.
The mesh is a simplified car geometry with PRISM volume layer on the car surface and the rest of the volume is Tetra/mixed with Meshing Method as Delauny.
The symm is the symmetry plane....

The error sequence in FLUENT is:
Building...
mesh
Note: Separating wall zone 20 into zones 20 and 1.
symm -> symm (20) and symm:001 (1)
Error:
FLUENT received fatal signal (ACCESS_VIOLATION)
1. Note exact events leading to error.
2. Save case/data under new name.
3. Exit program and restart to continue.
4. Report error to your distributor.

Please tell me what am I doing wrong and how to fix it...

yash.task.91 · March 30, 2012, 11:45

Hi..even I am getting the same error. Did u find out wats going wrong? Plz reply if you can.. yash.task.91@gmail.com
Thanks!

LuckyTran · March 31, 2012, 16:15

Not sure if the same reason is for your case but I have had this problem occur to me many times even though nothing was actually wrong.

In my case, it was either a licensing / mpi error. A loss of network connection often resulted in this error.

The error does not pop up immediately and is hard to detect. Sometimes I have been able to keep working, and even started iterating only to have the program crash 15 minutes later (after I have left the working computer). I come back the next day to find out that the simulation never finished!

March 28, 2012, 00:49	FLUENT received fatal signal (ACCESS_VIOLATION)	#1
osamaghani New Member Osama Join Date: Mar 2012 Posts: 26 Rep Power: 14	Hello! I am getting this error whenever I read the MESH in fluent. "FLUENT received fatal signal (ACCESS_VIOLATION)" I am using ICEM to create mesh. The mesh is a simplified car geometry with PRISM volume layer on the car surface and the rest of the volume is Tetra/mixed with Meshing Method as Delauny. The symm is the symmetry plane.... The error sequence in FLUENT is: Building... mesh Note: Separating wall zone 20 into zones 20 and 1. symm -> symm (20) and symm:001 (1) Error: FLUENT received fatal signal (ACCESS_VIOLATION) 1. Note exact events leading to error. 2. Save case/data under new name. 3. Exit program and restart to continue. 4. Report error to your distributor. Please tell me what am I doing wrong and how to fix it...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FLUENT received fatal signal (ACCESS_VIOLATION)	CHAKER	FLUENT	4	December 11, 2015 03:20
FLUENT received fatal signal (ACCESS_VIOLATION)	rubis	Fluent UDF and Scheme Programming	6	April 22, 2014 15:42
Problems in lauching FLUENT	Lourival	FLUENT	3	January 16, 2008 16:48
fatal signal (ACCESS_VIOLATION)	manu	FLUENT	0	December 10, 2007 06:10
FLUENT received fatal signal (ACCESS_VIOLATION)	samy	FLUENT	0	November 10, 2007 13:09

March 30, 2012, 11:45		#2
yash.task.91 New Member Yash Join Date: Mar 2012 Posts: 3 Rep Power: 14	Hi..even I am getting the same error. Did u find out wats going wrong? Plz reply if you can.. yash.task.91@gmail.com Thanks!

March 31, 2012, 16:15		#3
LuckyTran Senior Member Lucky Join Date: Apr 2011 Location: Orlando, FL USA Posts: 5,672 Rep Power: 65	Not sure if the same reason is for your case but I have had this problem occur to me many times even though nothing was actually wrong. In my case, it was either a licensing / mpi error. A loss of network connection often resulted in this error. The error does not pop up immediately and is hard to detect. Sometimes I have been able to keep working, and even started iterating only to have the program crash 15 minutes later (after I have left the working computer). I come back the next day to find out that the simulation never finished!