CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Natural convection

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   May 15, 2007, 08:34
Default Natural convection
  #1
Jozef
Guest
 
Posts: n/a
Hi, i need to program natural convection in 2D, for example hot plate high 10cm and colder water paralel to it. I know plate and water temperature and all coefficient(Prandtl, Grashof, density, ...) I can calculate heat transfer from plate to water, but i dont know how i should calculate next distance from plate and temperature them. How i can use heat transfer q=h.A.deltaT(h-coefficient, A-area, deltaT- difference between temperatures plate and water) for define it? Or how i can calculate temperature in water in next areas? Thanks a lot, Jozef
  Reply With Quote

Old   May 15, 2007, 11:48
Default Re: Natural convection
  #2
OPS
Guest
 
Posts: n/a
Delta T = T_hot - T_fluid.

Here T_hot is the temperature of the plate. T_hot is also the temperature of the fluid in contact with the plate. T_fluid is known from the calculation. It is the temperature of the ambient fluid. Note that when T_hot = T_fluid, no heat transfer by convection occur.

OPS
  Reply With Quote

Old   May 15, 2007, 12:27
Default Re: Natural convection
  #3
Jozef
Guest
 
Posts: n/a
Thanks OPS, but I wrote my question probably wrong or bad to understand. I know temperature T_hot and T_fluid too. But now, I need to know temperature T1, T2 ... I think that by natural convection temperature is position as i draw. And here is picture of my problem http://www.ukazto.com/img/otazka_forum.jpg or http://img411.imageshack.us/img411/6...kaforumfx3.png Thanks, Jozef
  Reply With Quote

Old   May 15, 2007, 12:55
Default Re: Natural convection
  #4
OPS
Guest
 
Posts: n/a
You need not know T1, T2 etc. By definition,

Q = k(T_hot - T_infinity), (1) and this is the maximum heat than can be transfered by convection. T_infinity is the far field fluid temperature.

Let me put this way.

Heat is conserved. So,

Q = k(T_hot - T1) = k(T_hot - T2) = k(T_hot - T1)

= k(T_hot - T_infinity)

If above equation is satisfied, then T1 = T2 = T_infinity.

OPS
  Reply With Quote

Old   May 15, 2007, 13:58
Default Re: Natural convection
  #5
Jozef
Guest
 
Posts: n/a
Thanks for your time, but still one question. I understand what you wrote, but..

1, I define Prandtl, Grashof number =>heat transfer koeficient for convection k. now Q=k(T_hot-T_fluid). This is between fluid on interface and "next" fluid. But i need to know temperature between this two points.

T1 and T2 cant be the same i think. Yeah, after some time T1=T2, but not immediately. And i need this state. Some idea how calculate temperature with some realistic measurements(eg. 0.01m-T=50°C,0.015m-45°C)? I need draw it to graph. Thanks, Jozef
  Reply With Quote

Old   May 16, 2007, 00:14
Default Re: Natural convection
  #6
OPS
Guest
 
Posts: n/a
Q=k(T_hot-T_fluid). This is between fluid on interface and "next" fluid.

The above formula is not for the "next fluid". Let me explain:

At time t = 0, Q1=HA(T_hot-T_fluid). This is the maximum amount of heat that will be transfered. Now for any subsequent time t>0, if one take T_fluid as T1 such that T1>T_fluid ( and this is what your are telling) then

Q2 = HA(T_hot - T1).

In this case Q1 > Q2. What happen to the excess heat (Q1-Q2)? So by taking T1, you are not conserving the heat.

And regarding knowing temperature between two points, then simulation will give you the answer. If you are doing simulation, then at each point in the domain, you can get T.

OPS

  Reply With Quote

Old   May 16, 2007, 09:47
Default Re: Natural convection
  #7
Jozef
Guest
 
Posts: n/a
So if i understand:

1, I use formula Q1=H1.L.(T_hot-T_fluid) where L is distance between points with temperature T_hot, T_fluid

2, I calculate Q2=H2.L.(T_hot-T1)

3, As you wrote, deltaQ=Q1-Q2

4, deltaQ=H3.Lx.(T1-T_fluid) where Lx is distance between points with temperature T1, T_fluid which i am looking for

5, Q1= Q2 + deltaQ = H2.L.(T_hot-T1)+H3.Lx.(T1-T_fluid)

H1, H2, H3 are diferent( function of temperature). The heat transfer Q1 is equal, but on different distance. Is it right? Thanks Jozef
  Reply With Quote

Old   May 16, 2007, 13:13
Default Re: Natural convection
  #8
OPS
Guest
 
Posts: n/a
Yes Mr. Jozef, you got it. If fact I had thought of writing the same thing what you have written. I appreciate your quick understanding.

OPS
  Reply With Quote

Old   May 16, 2007, 13:18
Default Re: Natural convection
  #9
Jozef
Guest
 
Posts: n/a
Thanks so much much OPS
  Reply With Quote

Old   May 17, 2007, 00:56
Default Re: Natural convection
  #10
OPS
Guest
 
Posts: n/a
You are most welcome Jozef !!!

OPS
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
natural convection problem with radiation jorien CFX 0 October 14, 2011 10:26
Natural Convection with heat generation krishnachandranr Main CFD Forum 0 July 28, 2009 05:22
Coupled vs Seg - Natural vs. Forced Convection Alex Siemens 5 December 12, 2007 05:58
natural convection at high Rayleigh mauricio FLUENT 2 February 23, 2005 20:43
Mixing By Natural Convection Processes Greg Perkins FLUENT 0 February 12, 2003 19:40


All times are GMT -4. The time now is 04:44.