CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Open source codes for VOF simulations

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   February 27, 2008, 07:50
Default Open source codes for VOF simulations
  #1
Asghari
Guest
 
Posts: n/a
Hi all.

Does anyone access to a free open-source code(not conventional commercial softwares such as FLUENT ,Starcd,...) simulaing VOF (volume of fluid) simulation ?

If you access to it, can I appeal you to send it for me?

What's geometry for it ?

It is preferable for me that code has been written by a program language such as (FORTRAN,Visual C, BASIC, MATHLAB,..).My email address is mehdiasgh@gmail.com

Thanks a lot for any help.

I need to this
  Reply With Quote

Old   February 27, 2008, 14:51
Default Re: Open source codes for VOF simulations
  #2
andy20
Guest
 
Posts: n/a
Try OpenFoam. You can look it up on the cfd-online website, and visit the OpenFOAM site and discussion forums at:

http://www.opencfd.co.uk/openfoam/

It can do dam-break type problems, as shown by the graphics on the page:

http://www.opencfd.co.uk/index.html

It runs best on Linux/Unix.

I have had no problems with OpenFOAM itself. However finding a suitable open-source 3-D meshing tool that can handle boundary layers for CFD calculations, etc has been very difficult.

Good luck, Andy

  Reply With Quote

Old   February 28, 2008, 05:22
Default Re: Open source codes for VOF simulations
  #3
A.K.
Guest
 
Posts: n/a
Hi, Andy! Have you really had no problems with OpenFOAM? I have heard that users face convergence problems with this solver. In particular, they need very small Courant number to get the convergence. This topic was under discussion in the OpenFOAM forum.
  Reply With Quote

Old   February 29, 2008, 05:25
Default Re: Open source codes for VOF simulations
  #4
andy20
Guest
 
Posts: n/a
A.K,

Sorry - I should have qualified my statement somewhat...

I haven't had any convergence problems with OpenFOAM on the problems I've used it for, which have been slow viscous flow in complex geometries.

I haven't been able to generate a mesh with suitable prisms at the boundary for the high speed gas flow problems I'm interested in. Therefore I haven't tried OpenFOAM for these more difficult cases, as I wouldn't trust results from any FVM code with any pure tetra grid in these geometries...

So I can't really advise on experience with convergence problems. Nevertheless, IMHO OpenFOAM does appear to be one of the most active and complete open source CFD suites around at the moment, supports the free surface flows the OP asked about, and there seems to be a lot of support available on the discussion forums. So I mantain it's worth a look for the OP...

Best regards, Andy
  Reply With Quote

Old   February 29, 2008, 18:10
Default Re: Open source codes for VOF simulations
  #5
alpha
Guest
 
Posts: n/a
Hi Andy

Its really difficult to generate complex geometries and meshes with blockMesh utility that OpenFOAM uses. Which software do you use? Are you aware of any open source software that could generate unstructured mesh and is compatible with OpenFOAM.

Thanks Alpha
  Reply With Quote

Old   March 2, 2008, 09:38
Default Re: Open source codes for VOF simulations
  #6
andy20
Guest
 
Posts: n/a
Alpha,

I agree - it seems very hard to find a good mesh generation tool for OpenFOAM. As I said in my last post, that is what has stopped me using it more often.

Netgen is often mentioned on the OpenFOAM forum. I think it is mainly a finite element tool though, as it only seems to generate fully tetrahedral meshes with no boundary layer / inflation meshing options. Therefore Netgen meshes are not really suitable for CFD. It is easy to use (but hard to compile - I suggest using a binary installation if possible).

GMesh also gets mentioned, but I've not yet used that successfully - and I don't yet know if it supports boundary layer meshes.

I hope that anyone else reading this thread will mention any good tools that they know of - because I think we would both like to learn about them!

Good luck, Andy
  Reply With Quote

Old   March 2, 2008, 21:12
Default Re: Open source codes for VOF simulations
  #7
alpha
Guest
 
Posts: n/a
Hi Andy

Unfortunately both netgen and Gmsh generate structured mesh where as i often need to take into account formation of boundary layer in my problems. I have recently started using OpenFOAM and found it very good tool for CFD analysis. Only problem that i am facing is generation of complex geometry and mesh. Thanks for your answer.

alpha
  Reply With Quote

Old   March 27, 2008, 19:18
Default Re: Open source codes for VOF simulations
  #8
Gert-Jan
Guest
 
Posts: n/a
GID?
  Reply With Quote

Old   March 28, 2008, 08:28
Default Re: Open source codes for VOF simulations
  #9
alpha
Guest
 
Posts: n/a
Sorry what is GID? Thanks
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
pisoFoam compiling error with OF 1.7.1 on MAC OSX Greg Givogue OpenFOAM Programming & Development 3 March 4, 2011 18:18
Problem installing on Ubuntu 9.10 -> 'Cannot open : No such file or directory' mfiandor OpenFOAM Installation 2 January 25, 2010 10:50
[OpenFOAM] ParaView 33 canbt open OpenFoam file hariya03 ParaView 7 September 25, 2008 18:33
DxFoam reader update hjasak OpenFOAM Post-Processing 69 April 24, 2008 02:24
OpenFOAM with IBM AIX matthias OpenFOAM Installation 20 March 25, 2008 03:36


All times are GMT -4. The time now is 06:39.