CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Help with unstanding Energy Equation

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   September 8, 2008, 08:19
Default Help with unstanding Energy Equation
  #1
siw
Guest
 
Posts: n/a
Hi,

I'm working through J D Andersons book CFD The Basics with Applications and I'm a bit confused with how he's putting together the energy equation.

The book states the energy equation (eq 2.59) is:

A = B + C where,

A - rate of change of energy inside fluid element. B - net flux of heat into element. C - rate of work done on element due to body and surface forces.

How does A = B + C equate? Because the units of A must be Joules per second as it's just dE/dt. The units of C must be the same as it's d(F * x)/dt with units [N m / s] = [J / s].

But with B the heat flux is [J / s m^2]. Which is not the same as [J / s] in A and C. If it was heat flow rate rather than heat flux then the units would match.

Am I missing something really simple. I'm working through the book and to me it does not work out. So I'd appreciate your help clarrifying this.

Thanks.
  Reply With Quote

Old   September 8, 2008, 09:55
Default Re: Help with unstanding Energy Equation
  #2
ag
Guest
 
Posts: n/a
Net energy change = heat transfer + work done on element

First law of thermodynamics
  Reply With Quote

Old   September 8, 2008, 10:36
Default Re: Help with unstanding Energy Equation
  #3
siw
Guest
 
Posts: n/a
So the book stating heat flux (heat energy per unit time per unit area) is incorret and it should be heat transfer (heat energy per unit time) then?
  Reply With Quote

Old   September 8, 2008, 11:30
Default Re: Help with unstanding Energy Equation
  #4
andy2O
Guest
 
Posts: n/a
You've just forgotten that the heat flux in question is the heat flux **over the surface of the element**. Thus:

B = net heat flux into the element

= Area integral of (heat flux at element surface) over the surface of element

Now performing an area integral introduces a term like [m^2]. So whilst the heat flux has units of [J/s m^2], by the time it's been integrated over the element's surface area you end up with [J/s] as required.

Regards, andy2o
  Reply With Quote

Old   September 8, 2008, 12:03
Default Re: Help with unstanding Energy Equation
  #5
Ananda Himansu
Guest
 
Posts: n/a
"flux" carries the meaning of "flow" or "current". Some authors use the term flux to signify time-rate of flow per unit area, and then may refer to the integral of this flux with respect to the area as the "total flux" or the "total flow rate". Whereas other authors, such as Anderson, use "flux" to signify the time-rate of flow through the entire area, and they may use "flux density" or "flux current density" to signify the time-rate of flow per unit area.
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Calculation of the Governing Equations Mihail CFX 7 September 7, 2014 07:27
ATTENTION! Reliability problems in CFX 5.7 Joseph CFX 14 April 20, 2010 16:45
Viscosity and the Energy Equation Rich Main CFD Forum 0 December 16, 2009 15:01
SIMPLE and energy equation convergence Fabio Main CFD Forum 0 June 1, 2007 07:06
question about energy equation zhou FLUENT 0 February 24, 2004 00:55


All times are GMT -4. The time now is 22:46.