CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > FLUENT

Modeling heat transfer through a porous media

Register Blogs Members List Search Today's Posts Mark Forums Read

Like Tree3Likes
  • 2 Post By Rami
  • 1 Post By mmunige

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   June 2, 2010, 16:13
Default Modeling heat transfer through a porous media
  #1
New Member
 
harinadh
Join Date: Jun 2010
Posts: 1
Rep Power: 0
harimighty is on a distinguished road
Hello,

I am a beginner, I am trying to model heat transfer through a porous medium.
I am modeling a cuboid in the design modeller, meshing it there and importing it into fluent.I am then modeling the fluid cell as a porous zone with given porosity and imposing the boundary conditions which include uniform heat flux on one surface and all the other surfaces adiabatic and velocity inlet boundary condition as well.
The heat flux does not seem to have any effect on the porous media, I am getting unform temperature contours through out the model.

Can some one tell me if I am doing the modeling right.

Thanks,
Harimighty.
harimighty is offline   Reply With Quote

Old   June 2, 2010, 18:08
Default
  #2
Senior Member
 
Aroon
Join Date: Apr 2009
Location: Racine WI
Posts: 148
Rep Power: 16
vishyaroon is on a distinguished road
Couple of related questions/comments:

1. What values of porosity are you using?
2. I have tried using porous media with a wall temperature too. Compared to such a case, my (limited) experience showed that using a heat source/sink workes better in porous media.
vishyaroon is offline   Reply With Quote

Old   June 3, 2010, 03:46
Default
  #3
Senior Member
 
Rami Ben-Zvi
Join Date: Mar 2009
Posts: 155
Rep Power: 17
Rami is on a distinguished road
Quote:
Originally Posted by harimighty View Post
Hello,

I am a beginner, I am trying to model heat transfer through a porous medium.
I am modeling a cuboid in the design modeller, meshing it there and importing it into fluent.I am then modeling the fluid cell as a porous zone with given porosity and imposing the boundary conditions which include uniform heat flux on one surface and all the other surfaces adiabatic and velocity inlet boundary condition as well.
The heat flux does not seem to have any effect on the porous media, I am getting unform temperature contours through out the model.

Can some one tell me if I am doing the modeling right.

Thanks,
Harimighty.

I had a somewhat similar problem in FLUENT, and could not get any satisfactory reply. Please refer to the following threads:
  • http://www.cfd-online.com/Forums/fluent/64958-including-radiation-when-temperature-expressed-uds-porous-media.html
  • http://www.cfd-online.com/Forums/fluent/48421-fluent-radiation-porous-media.html.
I'd like to hear whether and how it is indeed possible to treat a porous medium having two distinct temperatures (one for the fluid and one for the solid) and enabling heat transfer in it by convection (and also radiation and conduction).
PS: It would be better for you to post in the FLUENT forum than the present one.
Chr.D and souza.emer like this.
Rami is offline   Reply With Quote

Old   July 23, 2016, 06:11
Question Modelling heat flow in porous media
  #4
New Member
 
mm
Join Date: May 2016
Posts: 24
Rep Power: 8
mmunige is an unknown quantity at this point
Dear all,

I am modelling heat transfer through a porous medium in Fluent (from hot air to porous medium), have defined porous medium in fluid cell zone, resistance coefficients,
porosity, heat transfer coefficients since i am using non-equilibrium thermal model. this is transient 2D simulation. (a vertical column having porous material inside and top inlet for hot air and bottom outlet).

in start temperature distribution along the domain is fine and close to experimental values, but after 300 or 400 seconds temperature does not change or changes very little at all sections of domain and further it goes below the experimental values. I m using both fluid and solid properties as temperature dependent.
please guide me where i am doing wrong so I am not getting the uniform trend of temperature variation along the domain in whole simulation period.
please

Regards
amir_hiwa likes this.
mmunige is offline   Reply With Quote

Reply

Tags
porous medium

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
heat transfer in porous media Miko Siemens 10 February 16, 2022 08:13
Heat transfer within Porous Media Twiti CFX 10 January 15, 2021 09:13
Conjugate heat transfer problem with porous media piko Siemens 1 April 17, 2009 16:41
heat transfer with porous media gokul FLUENT 0 February 24, 2009 14:43
REG POROUS MEDIA HEAT TRANSFER Rashmi Venkat FLUENT 6 June 1, 2006 06:13


All times are GMT -4. The time now is 07:41.