CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > General Forums > Main CFD Forum

Role of divergence

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   June 20, 2005, 02:55
Default Role of divergence
  #1
shekharc
Guest
 
Posts: n/a
Hi,

I have finished my CFD calculation and to check it's accuracy, I analized the divergence in each cell. It is in order of 1.0E-4 ~ 1.0E-5 for the "internal" cells (where velocity and pressure fields are determined entirely by N.S. equation). However, it is in order of 1.0E-2 at the worst-grid(near the inlet). Please note that one of the neignbouring cells at this location is the Ghost-cell (at which the velocity field is estimated after satisfying the mass-conservation as mentioned in MAC by Harlow and Welch,...and then the pressure estimation is done using normal component of the N.S. equation).

I don't know how much does this worst grid spoil the solution and how to improve the situation.

Also, can a same criterion on divergence (e.g. Divergence < 1.0E-4 (say)) be used irrespective of grid size to check accouracy of the solution....i.e. if we get same divergence = 9.4E-5 for two cells having different grid sizesn a1 x b1 x c1 and a2 x b2 x c2 respectively, can we say that accuracy is almost same at both the cells. Here, "Divergence*Volume = Mass accumulation" in the cell.

Thanks in anticipation,

chandra.
  Reply With Quote

Old   June 21, 2005, 15:37
Default Re: Role of divergence
  #2
agg
Guest
 
Posts: n/a
The error will be slightly larger at boundaries because you are enforcing mass flow internally and then updating boundary velocities.

Mass flow conservation and grid resolution effects are two different issues. Whatever the grid size, mass flow should be conserved. Since solution to poisson equation is expensive (every time step), convergence is a trade-off between accuracy and computational time and you may have to do some tests before you can decide the right numbers for your application.

Another check for mass flow rate would be to actually integrate velocity over normal surface area at various cross sections.
  Reply With Quote

Old   June 22, 2005, 13:14
Default Re: Role of divergence
  #3
e_kang
Guest
 
Posts: n/a
The convergence criteria may be stricter for very fine grids (as small as 1e-07).
  Reply With Quote

Old   June 23, 2005, 15:11
Default Re: Role of divergence
  #4
shekharc
Guest
 
Posts: n/a
Thanks a lot for the suggestions...however, the variation of convergence criterion based on size of the grid seems to be a little confusing....if we see physical meaning of divergence, it is nothing but 'rate of mass accumulation per unit volume'...and so the selected divergence-criterion should be independent of the grid size...please suggest me if there are other things also which I am not able to point out as far as choosing of this divergence-criterion is concerned..

Also, as I already have mentioned in my previous posting, the inlet-grids having neighbouring-cells a Ghost-cell show very bad performance, could any of you please suggest me about the extent to which this bad cell can spoil the solution. I think answer of it is a matter of experience...and I am very new in it

thanks in advance,

chandra
  Reply With Quote

Old   June 23, 2005, 15:39
Default Re: Role of divergence
  #5
agg
Guest
 
Posts: n/a
chandra,

Satisfying divergence does depend a lot on the order of accuracy of numerical scheme. For example, using a second order finite difference scheme you might be able to get divergence as low as 1E-6. Using spectral methods divergence can be as low as 1E-16.

Also, in your code, you control divergence through solution to Poisson equation (is that right?). Hence you should use trial/error changing convergence criteria for pressure solution to see how if affects divergence.

Regarding higher divergence values at boundaries, i think that should not be a problem, since you do not actually solve Navier-Stokes equations at the boundary. So as long as your solution looks ok, I wouldn't worry too much about it.

  Reply With Quote

Old   July 5, 2005, 01:49
Default Re: Role of divergence
  #6
shekharc
Guest
 
Posts: n/a
heyy, thanks a lot but the divergence near the boundary is really worrying me...

Divergence in the cell adjacent to the inlet having ghost-cell a neighbour is having divergence in order of 100 times more than internal grids. I dont know how to improve the situation. I think refining the grid in this problematic region may do it but I am not sure. Please suggest me if there is any other way...

Thanks in anticipation...

--Chandra
  Reply With Quote

Old   July 5, 2005, 12:17
Default Re: Role of divergence
  #7
agg
Guest
 
Posts: n/a
I'm Sorry I do not know how to alleviate problem related to divergence near boundary. There might be papers that discuss this in detail.

Good luck.
  Reply With Quote

Old   July 5, 2005, 13:08
Default Re: Role of divergence
  #8
shekharc
Guest
 
Posts: n/a
Heyy man, thanks a lot for yr suggestions...I will search if there is any such kind of paper dealing with the issue..

thanks...chandra
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
UDF divergence of a vector cris FLUENT 3 September 4, 2014 19:06
Divergence problem for species transport model MY FLUENT 3 January 11, 2014 05:46
Quarter Burner mesh with periosic condition SamCanuck FLUENT 2 August 31, 2011 12:34
divergence in MAC Method Maciej Matyka Main CFD Forum 2 December 19, 2000 11:43
help:spectral methods & divergence free functionsn D. Puigjaner Main CFD Forum 1 August 28, 2000 11:06


All times are GMT -4. The time now is 04:36.