Flow in cylinder

nhosseini · December 18, 2011, 03:03

Hi every body!

I want to solve a transient, incompressible inviscid flow in a cylinder, which its initial condition is zero velocity everywhere and at delta t=1 left boundary condition is V boundary= Vb and for right boundary condition we have pressure= ambient pressure
it seems that all nodes velocities should reach Vb after 1 time step but I have problem while using conservation methods, it takes some more steps for nodes to reach Vb.
I would be so thankfull if somebody could help me.

Ford Prefect · December 18, 2011, 10:39

Quote:

Originally Posted by nhosseini

Hi every body!

I want to solve a transient, incompressible inviscid flow in a cylinder, which its initial condition is zero velocity everywhere and at delta t=1 left boundary condition is V boundary= Vb and for right boundary condition we have pressure= ambient pressure
it seems that all nodes velocities should reach Vb after 1 time step but I have problem while using conservation methods, it takes some more steps for nodes to reach Vb.
I would be so thankfull if somebody could help me.

What boundary condition do you have for pressure at the velocity inlet?

nhosseini · December 18, 2011, 11:22

no boundary condition, I solve mass equation in inlet for pressure

Ford Prefect · December 18, 2011, 15:23

What method do you use to couple velocity and pressure? Do you use some limited compressibility method or a fully incompressible method where div U = 0 ?

Is the behavior independent of time-step and Reynolds number (i.e. if you change dt or Re, will you reach Vb in the entire domain in fewer time-steps)?

nhosseini · December 18, 2011, 22:21

I use a pressure based method, and yes its behavior is depends on delta t, by increasing time step it reaches the Vb in fewer steps. and by omitting transient term whole field velocity reaches to Vb in one step which is desired, thank you

Ford Prefect · December 19, 2011, 03:45

Ok. I assume that you are solving some kind of Poisson equation for pressure and then you need a boundary condition for pressure at the inlet.

You state that you use continuity equation for this. Could you please show what you mean here?

Anyways, some methods specify a homogeneous Neumann condition for pressure at boundaries. However it might be better to use the normal momentum equation instead. By doing so you will compensate for grid size and time-step and the solution will be independent of the two. It will also converge within one time-step, given that your linear solver converges sufficiently.

nhosseini · December 19, 2011, 04:51

first of all thanks for your quick reply, as I am really confused with it.

I solve du/dx=0 for mass and I use finite element control volume method, so I use u* and u* is pressure based and is

Mass: U*e - Uinlet = 0

u*e =( Ui+Ui+1)/2 + (Pi-Pi+1)/(2*ro*u*e)
U inlet = Vb

and
Momentum: U inlet = Vb

you mean that I need one more condition for pressure?

December 18, 2011, 03:03	Flow in cylinder	#1
nhosseini New Member SNH Join Date: Dec 2011 Posts: 8 Rep Power: 14	Hi every body! I want to solve a transient, incompressible inviscid flow in a cylinder, which its initial condition is zero velocity everywhere and at delta t=1 left boundary condition is V boundary= Vb and for right boundary condition we have pressure= ambient pressure it seems that all nodes velocities should reach Vb after 1 time step but I have problem while using conservation methods, it takes some more steps for nodes to reach Vb. I would be so thankfull if somebody could help me.

December 18, 2011, 15:23		#4
Ford Prefect Senior Member Join Date: Mar 2009 Posts: 151 Rep Power: 17	What method do you use to couple velocity and pressure? Do you use some limited compressibility method or a fully incompressible method where div U = 0 ? Is the behavior independent of time-step and Reynolds number (i.e. if you change dt or Re, will you reach Vb in the entire domain in fewer time-steps)? __________________ "Trying is the first step to failure." - Homer Simpson

December 19, 2011, 03:45		#6
Ford Prefect Senior Member Join Date: Mar 2009 Posts: 151 Rep Power: 17	Ok. I assume that you are solving some kind of Poisson equation for pressure and then you need a boundary condition for pressure at the inlet. You state that you use continuity equation for this. Could you please show what you mean here? Anyways, some methods specify a homogeneous Neumann condition for pressure at boundaries. However it might be better to use the normal momentum equation instead. By doing so you will compensate for grid size and time-step and the solution will be independent of the two. It will also converge within one time-step, given that your linear solver converges sufficiently. __________________ "Trying is the first step to failure." - Homer Simpson

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
benchmark: flow over a circular cylinder	goodegg	Main CFD Forum	12	January 22, 2013 11:47
1 Was FSI for a flow over a cylinder	vmlxb6	CFX	17	May 16, 2011 02:29
Moving a Cylinder in cross flow after solving Dynamics equations of motion	maruthamuthu_venkatraman	OpenFOAM	1	November 19, 2009 13:55
Flow over a flat plate & Flow over a cylinder	cfdxue	Main CFD Forum	0	November 26, 2007 23:26
Flow over a cylinder	Anna	Main CFD Forum	9	March 24, 2006 14:32

December 18, 2011, 11:22		#3
nhosseini New Member SNH Join Date: Dec 2011 Posts: 8 Rep Power: 14	no boundary condition, I solve mass equation in inlet for pressure

December 18, 2011, 22:21		#5
nhosseini New Member SNH Join Date: Dec 2011 Posts: 8 Rep Power: 14	I use a pressure based method, and yes its behavior is depends on delta t, by increasing time step it reaches the Vb in fewer steps. and by omitting transient term whole field velocity reaches to Vb in one step which is desired, thank you

December 19, 2011, 04:51		#7
nhosseini New Member SNH Join Date: Dec 2011 Posts: 8 Rep Power: 14	first of all thanks for your quick reply, as I am really confused with it. I solve du/dx=0 for mass and I use finite element control volume method, so I use u* and u* is pressure based and is Mass: Ue - Uinlet = 0 ue =( Ui+Ui+1)/2 + (Pi-Pi+1)/(2rou*e) U inlet = Vb and Momentum: U inlet = Vb you mean that I need one more condition for pressure?