NUMECA

Page 1 of 6

Threads in Forum : NUMECA

Rating Thread / Thread Starter	Last Post	Replies	Views
problem with translation johncarouche	July 2, 2009 04:52 by johncarouche	0	28
How to run numeca in serial/parallel mode? sangamesh	June 30, 2009 10:26 by sangamesh	0	32
"spanwise line broken ?" liang	June 26, 2009 05:10 by liang	0	44
discontinuity of 180° in leading edge(NUMECA autogrid) johncarouche	June 24, 2009 09:31 by johncarouche	0	47
Hi Does panle method can simulate turbofan？ lotaha	June 10, 2009 06:23 by lotaha	0	106
Trial version of NUMECA prasad	February 22, 2009 06:57 by prasad	0	740
block tridiagonal george kokkinakis	February 7, 2009 03:22 by Fateme Cheini	1	426
Why Manual recommends B-L model for sepating flow? Alex	February 5, 2009 10:14 by Alex	0	353
Autogrid: discontinuity of 90 degrees in shroud Eric Joubarne	January 26, 2009 09:15 by Eric Joubarne	0	312
k and epsilon discretization of RNG model mehran	January 24, 2009 00:01 by mehran	0	324
nasa rotor 67 or 37 geometry sam	December 23, 2008 18:35 by Hong S. IM	18	759
Switching Forum Software, Opinions Wanted Jonas Larsson	November 29, 2008 06:20 by Jonas Larsson	0	296
Skewness angle Jwala	November 13, 2008 06:57 by Jwala	0	343
Airfoil simulation using moving wall Alejandro	November 4, 2008 02:00 by Rajiv Kaul	9	821
thin extrusion meshing guillaume	October 27, 2008 19:39 by guillaume	0	294
Block Managment Xamar	October 24, 2008 05:10 by Xamar	0	299
I want to know which software will be best hanman	October 7, 2008 03:05 by anil kumar	2	388
Boundary conditions for rotating fan rohit	September 24, 2008 07:18 by Zhigang Liu	3	451
Orr-Sommerfeld equation Mojtaba Ahmadi	September 8, 2008 04:21 by Mojtaba Ahmadi	0	439
Memory allocation failed ??? Rikio	September 2, 2008 06:03 by jesse	3	534
How to simulate a static pressure sensor ? axel cole	August 22, 2008 20:01 by arthur	1	434
The radial stator-rotor seal liu wangkou	August 22, 2008 19:48 by arthur	1	358
autogrid:leading edge liu wangkou	August 22, 2008 19:42 by arthur	2	369
Can CFview reads CGNS ? Vinayender	July 23, 2008 08:17 by Vinayender	7	457
boiling inside porous John	July 17, 2008 20:38 by John	0	290
propeller blade meshing Terence	July 15, 2008 13:31 by Aji	8	522
what is isentropic mach number? peck110	July 9, 2008 13:18 by SA	6	453
convergence, numeca rsi	July 9, 2008 03:34 by Srinu	1	332
corner sepration Magic	June 30, 2008 18:11 by Magic	0	292
LES: Energy spectrum Hummi	June 16, 2008 16:21 by Hummi	0	339
input RPM profile? Lee Sangdo	May 7, 2008 09:57 by Jin-Kwon KIM	1	318
non-condensable gases for water Xa	April 4, 2008 06:52 by Xa	0	368
heat conducting in a solid domain Rogerio Fernandes Brito	March 18, 2008 18:24 by Rogerio Fernandes Brito	0	297
FDM discretization ...?? MS	March 2, 2008 19:05 by MS	0	301
HELP ME!!! I cannot import blade in autogrid! Nicola	February 1, 2008 03:38 by Jonathan Vlastuin	2	364
memory allocation failed Li Yijin	January 29, 2008 21:42 by Li Yijin	3	389
gridgeneration and file import from unigraphics nx Bucke Flo	January 26, 2008 04:46 by prashant	2	429
not enough basic knowledge -Marine potential client from Netherland	December 23, 2007 10:09 by potential client from Netherland	0	294
import .dat Datei Bucke Flo	December 17, 2007 02:38 by Bucke Flo	2	343
Transiet simulation of natural gas pipe line shahryar	December 8, 2007 05:10 by Vmin Yuan	1	458

Page 1 of 6

Last »

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 20:55.