Parallel Simulation Numeca Fine

daxterss · July 27, 2012, 03:33

Hello,

I am trying to run a simulation with a parallel computation. My computer has 4 cores. I open the Task Definition Window and I activate the option parallel computation and when I try to run it, a window appear and is like is going to start but the simulation doesn't start. This windows shows "start_status_ok" but the simulation doesn't run.

Can anybody help me?? Thanks in advance

daxterss · July 27, 2012, 03:46

More information: I use Windows 64 bits... can be because of the system??

oldshoes81 · July 30, 2012, 01:37

Hi,

Could i know what version of NUMECA FINE you are using and what type of Windows you have?

Before you could do so, you will have to make sure that your license does support for multi-cores up to 4 cores (for your case). Secondly, if the license does meet your requirement, make sure you register the MPIregister.exe and wpiregister.exe (in \bin directory) and key in your username and password that you use to log in the windows. if you do not have one, please create it.

Lastly, make sure the smpd.exe is pointed from /bin64.

I will encourage you to reach to your local support as the set up may a bit complicated.

daxterss · July 31, 2012, 07:36

Thanks a lot!!!
It is working now!!

)
Thanks!

daxterss · September 11, 2012, 07:45

Hello again
I would like to run the simlation in LINUX now... but there is a problem and I can't.
Anybody knows how i can use "ssh" instead of "rsh" (it is by default this last one)
Thanks in advance

oldshoes81 · September 11, 2012, 22:00

Hi,

Anyway you could reach to your local support on this manner? I believe they will happy to help you. By the way, may i know where are you located?

micalcheung · June 24, 2013, 04:52

I have the same problem with you
I wanna know how did you solve the problem
could you do me a favor ?
thanks a lot

July 27, 2012, 03:33	Parallel Simulation Numeca Fine	#1
daxterss New Member Mark Join Date: Mar 2012 Posts: 20 Rep Power: 14	Hello, I am trying to run a simulation with a parallel computation. My computer has 4 cores. I open the Task Definition Window and I activate the option parallel computation and when I try to run it, a window appear and is like is going to start but the simulation doesn't start. This windows shows "start_status_ok" but the simulation doesn't run. Can anybody help me?? Thanks in advance

July 30, 2012, 01:37		#3
oldshoes81 Member CJ Join Date: Apr 2010 Location: Malaysia Posts: 69 Rep Power: 15	Hi, Could i know what version of NUMECA FINE you are using and what type of Windows you have? Before you could do so, you will have to make sure that your license does support for multi-cores up to 4 cores (for your case). Secondly, if the license does meet your requirement, make sure you register the MPIregister.exe and wpiregister.exe (in \bin directory) and key in your username and password that you use to log in the windows. if you do not have one, please create it. Lastly, make sure the smpd.exe is pointed from /bin64. I will encourage you to reach to your local support as the set up may a bit complicated. Young G likes this. __________________ Regards CJ NUMIT Enterprise, Malaysia +6 017 656 3436 http://maccom-numit.blogspot.com http://www.numit.com.my Email : seiko.q@numit.com.my

September 11, 2012, 22:00		#6
oldshoes81 Member CJ Join Date: Apr 2010 Location: Malaysia Posts: 69 Rep Power: 15	Hi, Anyway you could reach to your local support on this manner? I believe they will happy to help you. By the way, may i know where are you located? __________________ Regards CJ NUMIT Enterprise, Malaysia +6 017 656 3436 http://maccom-numit.blogspot.com http://www.numit.com.my Email : seiko.q@numit.com.my

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rigid body motion error when restarting a terminated FSI simulation	lingdeer	ANSYS	1	May 19, 2013 01:40
is there some introduction of numeca fine?	timothygao	Fidelity CFD	0	March 4, 2011 08:34
Simulation doesn't meet reality	Hans	FloEFD, FloWorks & FloTHERM	1	June 9, 2010 08:59
Numeca Fine/Hexa simulation of catalytic converter	jackr84	Fidelity CFD	7	April 15, 2010 03:07
Parallel Simulation using Star-CCM+	SG	Siemens	5	March 11, 2008 10:52

July 27, 2012, 03:46		#2
daxterss New Member Mark Join Date: Mar 2012 Posts: 20 Rep Power: 14	More information: I use Windows 64 bits... can be because of the system??

July 31, 2012, 07:36		#4
daxterss New Member Mark Join Date: Mar 2012 Posts: 20 Rep Power: 14	Thanks a lot!!! It is working now!! ) Thanks!

September 11, 2012, 07:45		#5
daxterss New Member Mark Join Date: Mar 2012 Posts: 20 Rep Power: 14	Hello again I would like to run the simlation in LINUX now... but there is a problem and I can't. Anybody knows how i can use "ssh" instead of "rsh" (it is by default this last one) Thanks in advance

June 24, 2013, 04:52		#7
micalcheung New Member 陈金鑫 Join Date: Mar 2012 Posts: 2 Rep Power: 0	I have the same problem with you I wanna know how did you solve the problem could you do me a favor ? thanks a lot