Gentoo Ebuild

codygo · March 24, 2009, 19:59

I've compiled openFOAM via a gentoo ebuild. I started the first tutorial (icoFOAM/cavity) but openFOAM could not find paraview. After searching my system, i could not find a paraview program, even though it was supposedly successfully emerged, only a directory /usr/lib64/paraview3.4 with other files. I've tried paraview3.3-pre(...) and currently have paraview3.4 installed.

dmoroian · March 25, 2009, 02:12

Check your environment variables (etc/bashrc and etc/settings.sh). I remember that in the development version, the path to paraview was missing a "-".

Dragos

codygo · March 25, 2009, 11:43

I was able to download the paraview 3.4 binary from paraview.org, and adjusted all the variables so that I could run paraview. Now when I run paraFOAM it finds paraview, and it begins to open but crashes, qt then prints out an error message.

I've discovered that the gentoo ebuild for paraview disables qt4, that's why it doesn't create a paraview program. I've resorted to using foamToVTK and opening files with paraview directly.

bastil · March 28, 2009, 05:29

I am not aware of an GENTOO ebuild. Where did you get if from, please?

codygo · March 28, 2009, 14:19

It's available via the sunrise overlay. You can follow the gentoo overlay howto if you haven't set one up already. http://en.gentoo-wiki.com/wiki/Overlay

March 24, 2009, 19:59	Gentoo Ebuild	#1
codygo New Member cody Join Date: Mar 2009 Posts: 9 Rep Power: 17	I've compiled openFOAM via a gentoo ebuild. I started the first tutorial (icoFOAM/cavity) but openFOAM could not find paraview. After searching my system, i could not find a paraview program, even though it was supposedly successfully emerged, only a directory /usr/lib64/paraview3.4 with other files. I've tried paraview3.3-pre(...) and currently have paraview3.4 installed.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Gentoo ebuild for OpenFOAM141	deepblue17	OpenFOAM Installation	3	July 29, 2010 09:27
Gentoo Compilation woes on AMD64 with fluentMeshToFoamL	connclark	OpenFOAM Installation	8	February 29, 2008 14:18
Letbs create a Gentoo ebuild for OpenFOAM	danieltourde	OpenFOAM Installation	1	December 1, 2006 22:48
Sshd amp libelfso0 on gentoo box	alfreed	OpenFOAM Installation	2	June 15, 2006 10:05
Building on Sparc64 running gentoo	parra	OpenFOAM Installation	0	May 5, 2006 15:17

March 25, 2009, 02:12		#2
dmoroian Senior Member Dragos Join Date: Mar 2009 Posts: 648 Rep Power: 20	Check your environment variables (etc/bashrc and etc/settings.sh). I remember that in the development version, the path to paraview was missing a "-". Dragos

March 25, 2009, 11:43		#3
codygo New Member cody Join Date: Mar 2009 Posts: 9 Rep Power: 17	I was able to download the paraview 3.4 binary from paraview.org, and adjusted all the variables so that I could run paraview. Now when I run paraFOAM it finds paraview, and it begins to open but crashes, qt then prints out an error message. I've discovered that the gentoo ebuild for paraview disables qt4, that's why it doesn't create a paraview program. I've resorted to using foamToVTK and opening files with paraview directly.

March 28, 2009, 05:29		#4
bastil Senior Member BastiL Join Date: Mar 2009 Posts: 530 Rep Power: 20	I am not aware of an GENTOO ebuild. Where did you get if from, please?

March 28, 2009, 14:19		#5
codygo New Member cody Join Date: Mar 2009 Posts: 9 Rep Power: 17	It's available via the sunrise overlay. You can follow the gentoo overlay howto if you haven't set one up already. http://en.gentoo-wiki.com/wiki/Overlay