[Other] Mesh Conversion: OpenFoam (polyMesh format) to Calculix

gillers18 · April 21, 2015, 07:18

Hello All,

Currently working on a Problem dealing with Fluid Sturcture Interaction using the both programms OpenFoam and Calculix. I have already done the CFD Simulation in Open Foam and the results have been stored in OpenFoam polymesh format. Now I would like to use these Results to perform the FEM-Simulation, but Calculix can´t read these results because the exported polymesh contains some elements, which are not available in Calculix(only Hexa8 elements are supported).

How do i go about converting the polymesh from Openfoam in a mesh format with only hexa8 elements? Is there a converter available for this case?

Best Regards

Thierry

hjasak · April 22, 2015, 03:37

You need to decompose the polyhedral cells into shapes your software can understand. Paraview converter/module has a similar problem, so you can find code snippets there.

Hrv

gillers18 · April 24, 2015, 03:37

Thx fo your help. I really appreciate it.
Actually I m not used to work with the Paraview Converter /Module. Could you please explain me how to go about finding the code snippets on that module, which could help me to decompose the Polyhedral cells?

Best Regards

Thierry

April 21, 2015, 07:18	Mesh Conversion: OpenFoam (polyMesh format) to Calculix	#1
gillers18 New Member Join Date: Feb 2015 Location: Stuttgart Posts: 7 Rep Power: 11	Hello All, Currently working on a Problem dealing with Fluid Sturcture Interaction using the both programms OpenFoam and Calculix. I have already done the CFD Simulation in Open Foam and the results have been stored in OpenFoam polymesh format. Now I would like to use these Results to perform the FEM-Simulation, but Calculix can´t read these results because the exported polymesh contains some elements, which are not available in Calculix(only Hexa8 elements are supported). How do i go about converting the polymesh from Openfoam in a mesh format with only hexa8 elements? Is there a converter available for this case? Best Regards Thierry

April 22, 2015, 03:37		#2
hjasak Senior Member Hrvoje Jasak Join Date: Mar 2009 Location: London, England Posts: 1,905 Rep Power: 33	You need to decompose the polyhedral cells into shapes your software can understand. Paraview converter/module has a similar problem, so you can find code snippets there. Hrv gillers18 likes this. __________________ Hrvoje Jasak Providing commercial FOAM/OpenFOAM and CFD Consulting: http://wikki.co.uk

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Map of the OpenFOAM Forum - Understanding where to post your questions!	wyldckat	OpenFOAM	10	September 2, 2021 05:29
CFD by anderson, chp 10.... supersonic flow over flat plate	varunjain89	Main CFD Forum	18	May 11, 2018 07:31
[Commercial meshers] mesh conversion from ansys mesher to openfoam	Dusan1224	OpenFOAM Meshing & Mesh Conversion	2	November 5, 2015 03:41
[Salome] Mesh conversion Salome to OpenFOAM	VMartinez	OpenFOAM Meshing & Mesh Conversion	11	April 21, 2014 02:54
[Gmsh] 2D Mesh Generation Tutorial for GMSH	aeroslacker	OpenFOAM Meshing & Mesh Conversion	12	January 19, 2012 03:52

April 24, 2015, 03:37		#3
gillers18 New Member Join Date: Feb 2015 Location: Stuttgart Posts: 7 Rep Power: 11	Thx fo your help. I really appreciate it. Actually I m not used to work with the Paraview Converter /Module. Could you please explain me how to go about finding the code snippets on that module, which could help me to decompose the Polyhedral cells? Best Regards Thierry