CFD Online Logo CFD Online URL
Home > Forums > OpenFOAM Other Meshers: ICEM, Star, Ansys, Pointwise, GridPro, Ansa, ...

Line 137 BlockMeshDict Problems using ICEM

Register Blogs Members List Search Today's Posts Mark Forums Read

LinkBack Thread Tools Display Modes
Old   August 13, 2013, 14:10
Post Line 137 BlockMeshDict Problems using ICEM
New Member
Join Date: Aug 2013
Posts: 4
Rep Power: 4
agval79 is on a distinguished road
Dear all,
I'm new using OpenFOAM. I have been meshing with ICEM for some time, and I want to start using OF for solving my case studies. When I converted my mesh to OpenFOAM and ran blockMesh, I got this message:

// * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * //
Create time

Cannot open mesh description file

From function blockMesh
in file blockMeshApp.C at line 137.

FOAM exiting

Following the advice of this Forum, I checked the mesh. And apparently is a good one:

Checking geometry...
Overall domain bounding box (-64.5905 -18 -2.4869e-14) (23.0393 180 129.809)
Mesh (non-empty, non-wedge) directions (1 1 1)
Mesh (non-empty) directions (1 1 1)
Boundary openness (6.36975e-15 3.3617e-17 -7.55325e-16) OK.
Max cell openness = 2.71694e-16 OK.
Max aspect ratio = 8.01504 OK.
Minimum face area = 0.417017. Maximum face area = 93.2732. Face area magnitudes OK.
Min volume = 0.750633. Max volume = 282.629. Total volume = 929091. Cell volumes OK.
Mesh non-orthogonality Max: 55.609 average: 7.48596
Non-orthogonality check OK.
Face pyramids OK.
Max skewness = 1.5071 OK.
Coupled point location match (average 0) OK.

Mesh OK.


Tried blockMesh again with the same result. Then I ran another mesh that a friend helped me to create using Snappy. This mesh works very well. However, I want to do my own meshes using ICEM. Do you have a clue of what is going on?

agval79 is offline   Reply With Quote

Old   August 14, 2013, 01:22
Super Moderator
-mAx-'s Avatar
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,016
Rep Power: 31
-mAx- will become famous soon enough
blockMesh or snappyHexMesh are mesher. So if you already have your mesh with ICEM, why do you want to re-create one?
You only need to import your ICEM-mesh
In memory of my friend Hervé: CFD engineer & freerider
-mAx- is offline   Reply With Quote

Old   August 14, 2013, 04:14
Red face
New Member
Join Date: Aug 2013
Posts: 4
Rep Power: 4
agval79 is on a distinguished road
Thank you very much -mAx-. It's working very well now. I had the impression from the tutorials that blockMesh was always required previous to any running to UPLOAD the geometry in paraFoam. Thanks.
agval79 is offline   Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with Gmsh nishant_hull Open Source Meshers: Gmsh, Netgen, CGNS, ... 23 August 5, 2015 02:09
Problem of compilation OF 14Allwmake command not found erik_d OpenFOAM Bugs 13 September 13, 2008 21:45
GMSH and OpenFOAM derath OpenFOAM Mesh Utilities 44 September 4, 2008 05:09
Problems with ICEM? FYI ! Toralf Main CFD Forum 0 November 7, 2007 07:33
Problems of Duns Codes! Martin J Main CFD Forum 8 August 14, 2003 23:19

All times are GMT -4. The time now is 19:48.