CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > OpenFOAM > OpenFOAM Meshing & Mesh Conversion

[snappyHexMesh] Mesh becoming coarser during addLayers in sHM

Register Blogs Members List Search Today's Posts Mark Forums Read

Like Tree1Likes
  • 1 Post By eugene

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   December 13, 2010, 12:49
Default Mesh becoming coarser during addLayers in sHM
  #1
Senior Member
 
Arne Stahlmann
Join Date: Nov 2009
Location: Hanover, Germany
Posts: 209
Rep Power: 17
Arnoldinho is on a distinguished road
Hi,

I set up a test case for testing snappyHexMesh and especially the layer addition possibility.
I noticed that after the addLayers process, the surface mesh of my structure has become coarser, i.e. points and edges from the fine surface mesh (time 0.06) seem to have been used for the layer creation (time 0.09, vertical edges). Interestingly, this only happens on the cylinder part, not on the box part.

How can I stop this, as it is destroying my mesh in certain locations of the 'real' structure?

Pictures. left: after snapping procedure 0.06 right: after addLayers procedure 0.09.

The sHM dict is attached.
Attached Files
File Type: txt snappyHexMeshDict.txt (9.6 KB, 27 views)
Arnoldinho is offline   Reply With Quote

Old   December 14, 2010, 04:04
Default
  #2
Senior Member
 
Arne Stahlmann
Join Date: Nov 2009
Location: Hanover, Germany
Posts: 209
Rep Power: 17
Arnoldinho is on a distinguished road
Ok, let's ask another question: Is this a 'normal' behaviour of sHM, i.e. does this happen in a similar way in your cases, or not?
Arnoldinho is offline   Reply With Quote

Old   January 21, 2011, 09:17
Default
  #3
Member
 
Jim Knopf
Join Date: Dec 2010
Posts: 60
Rep Power: 15
JimKnopf is on a distinguished road
Do you have some pictures? I'm not sure about the phenomena you're describing

THX
jim
JimKnopf is offline   Reply With Quote

Old   February 22, 2011, 07:44
Default
  #4
New Member
 
Shankar
Join Date: Jun 2009
Location: India
Posts: 9
Rep Power: 16
shankar1221989 is on a distinguished road
Hello Arnoldinho,
Your observation is right, i too have seen this strange behavior while generating boundary layer padding.
As of know i am also not aware of the real reason.
shankar1221989 is offline   Reply With Quote

Old   April 6, 2011, 13:20
Default
  #5
Senior Member
 
Eugene de Villiers
Join Date: Mar 2009
Posts: 725
Rep Power: 21
eugene is on a distinguished road
The volume mesh isn't getting coarser. You are just observing a surface effect. Before the layers are added, SHM tries to merge all boundary faces in a cell that are close to co-planar to improve quality and reduce the number of added layer cells. The "coarsening" you are seeing on the cylinder is just this. Make a cutting plane normal to the cylinder and you will see. The reason you don't observe this on the box is because there much fewer same-cell co-planar faces on a coordinate aligned box.
skeptik likes this.
eugene is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
how to set periodic boundary conditions Ganesh FLUENT 15 November 18, 2020 07:09
decomposePar problem: Cell 0contains face labels out of range vaina74 OpenFOAM Pre-Processing 37 July 20, 2020 06:38
[snappyHexMesh] Snappyhex mesh: poor inlet mesh Swagga5aur OpenFOAM Meshing & Mesh Conversion 1 December 3, 2016 17:59
[snappyHexMesh] SHM not snapping to some surfaces Swift OpenFOAM Meshing & Mesh Conversion 13 January 4, 2016 02:56
engrid: Internal volume mesh becoming coarser during boundayr layer addition Arnoldinho OpenFOAM 1 January 22, 2011 05:31


All times are GMT -4. The time now is 09:08.