|
[Sponsors] |
[snappyHexMesh] nonManifoldPoints using snappyHexMesh |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
September 24, 2012, 09:03 |
nonManifoldPoints using snappyHexMesh
|
#1 |
Senior Member
Andrea Ferrari
Join Date: Dec 2010
Posts: 319
Rep Power: 16 |
HI foamers,
i am using snappyHexMEsh to mesh a complex geometry. I am doing some test, varying the number of cells of the backgroud mesh, to see which discretization is better for my simulation. In same cases, when the meshing process is finished, checkMesh returns a nonManifoldPoints warning like the one below Code:
Mesh stats points: 2554663 faces: 6609516 internal faces: 5603097 cells: 2023593 boundary patches: 7 point zones: 0 face zones: 0 cell zones: 0 Overall number of cells of each type: hexahedra: 2008426 prisms: 0 wedges: 0 pyramids: 0 tet wedges: 0 tetrahedra: 0 polyhedra: 15167 Checking topology... Boundary definition OK. Point usage OK. Upper triangular ordering OK. Face vertices OK. Number of regions: 1 (OK). Checking patch topology for multiply connected surfaces ... Patch Faces Points Surface topology left 23766 25072 ok (non-closed singly connected) right 22929 24290 ok (non-closed singly connected) top 5476 5625 ok (non-closed singly connected) bottom 17704 18749 ok (non-closed singly connected) front 22057 23326 ok (non-closed singly connected) back 23799 25100 ok (non-closed singly connected) square_CreatedbyGmsh890688 890541 multiply connected (shared edge) <<Writing 10 conflicting points to set nonManifoldPoints Checking geometry... Overall domain bounding box (0.001 0.001 0.001) (0.023 0.03 0.023) Mesh (non-empty, non-wedge) directions (1 1 1) Mesh (non-empty) directions (1 1 1) Boundary openness (9.0038e-14 6.34549e-14 3.07148e-15) OK. Max cell openness = 2.23352e-16 OK. Max aspect ratio = 1.00626 OK. Minumum face area = 2.2082e-08. Maximum face area = 8.88927e-08. Face area magnitudes OK. Min volume = 3.29904e-12. Max volume = 2.64278e-11. Total volume = 7.18693e-06. Cell volumes OK. Mesh non-orthogonality Max: 25.3111 average: 3.25383 Non-orthogonality check OK. Face pyramids OK. Max skewness = 0.333842 OK. I am using OF 2.1.0, but i have also tried 1.7.1 and got the same error. Best Andrea |
|
October 2, 2021, 18:55 |
|
#2 |
Member
Mohammad M F
Join Date: Jan 2016
Location: Washington DC, USA
Posts: 43
Rep Power: 10 |
Did OpenFOAM complain about nonManifoldPoint during the simulation?
I am also meshing a relatively complex geometry using sHM, and getting nonManifoldPoints warning? |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[CAD formats] Creating waterproof STL using snappyHexMesh or salome | Tobi | OpenFOAM Meshing & Mesh Conversion | 58 | May 13, 2020 06:01 |
[snappyHexMesh] Running snappyHexMesh in parallel - optimizing | peterhess | OpenFOAM Meshing & Mesh Conversion | 2 | January 3, 2018 02:54 |
[snappyHexMesh] Tutorial crashes: snappyHexMesh floating point exception. | jasv | OpenFOAM Meshing & Mesh Conversion | 4 | May 10, 2016 02:55 |
Strange Results With snappyHexMesh | calebamiles | OpenFOAM Running, Solving & CFD | 0 | August 14, 2011 16:02 |
[snappyHexMesh] stitchMesh and snappyHexMesh | gdbaldw | OpenFOAM Meshing & Mesh Conversion | 0 | December 23, 2009 02:09 |