[Netgen] Error message when exporting to OpenFOAM 1.5 + format

almir · May 16, 2011, 04:05

Hi,
I have a problem when I´m want to export the mesh to OpenFOAM 1.5+ format. Im using Netgen 4.9.13 for Windows. The programm brings me always the message:

Write OpenFOAM 1.5+ Mesh Files....
Export Error: Invalid mesh.... Aborting!
Export mesh to file .... DONE!

First I have tested the Netgen with a small testpart and a excerpt from the my part i need this part maybe was 30cm long and the export funktion worked great. The part I wont to make my reserches is 1.5m long, maybe thats the problem???

greets

philippose · May 18, 2011, 14:23

Hi,

A Good Evening to you !!

Hmmmm.... I use this export function almost every day, so I know that it is definitely working...

Question from my side is..... did Netgen successfully mesh the geometry you were trying to export into OpenFOAM? For the OpenFOAM export to work, you need to have the 3D Tet mesh too..... It does not work with just a 2D mesh.

Also, you can only export linear elements.... if you asked Netgen to create second order elements, the export will not work.

Hope this helps you come further :-)!

Have a nice day!

Philippose

almir · May 25, 2011, 04:30

hi,

now i have solved my problem.
My geometry was to complicated, there were to many small curves. This curves have no influence flow, but for the programm there was to many to calculate, which i don´t need.

greets

May 16, 2011, 04:05	Error message when exporting to OpenFOAM 1.5 + format	#1
almir New Member Join Date: May 2011 Location: Germany/Bosnia Posts: 9 Rep Power: 14	Hi, I have a problem when I´m want to export the mesh to OpenFOAM 1.5+ format. Im using Netgen 4.9.13 for Windows. The programm brings me always the message: Write OpenFOAM 1.5+ Mesh Files.... Export Error: Invalid mesh.... Aborting! Export mesh to file .... DONE! First I have tested the Netgen with a small testpart and a excerpt from the my part i need this part maybe was 30cm long and the export funktion worked great. The part I wont to make my reserches is 1.5m long, maybe thats the problem??? greets

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Commercial meshers] About the Commercial and Closed Source Meshers discussed here	wyldckat	OpenFOAM Meshing & Mesh Conversion	3	July 22, 2020 22:09
OpenFOAM course for beginners	Jibran	OpenFOAM Announcements from Other Sources	2	November 4, 2019 08:51
OpenFOAM Training Jan-Jul 2017, Virtual, London, Houston, Berlin	CFDFoundation	OpenFOAM Announcements from Other Sources	0	January 4, 2017 06:15
Problem installing OpenFOAM 1.5 installation on RHEL 4.	vwsj84	OpenFOAM Installation	4	April 23, 2009 04:48
OpenFOAM Version 1.5 Released	OpenFOAM discussion board administrator	OpenFOAM Announcements from ESI-OpenCFD	0	July 14, 2008 18:22

May 18, 2011, 14:23		#2
philippose Senior Member Philippose Rajan Join Date: Mar 2009 Location: Germany Posts: 552 Rep Power: 25	Hi, A Good Evening to you !! Hmmmm.... I use this export function almost every day, so I know that it is definitely working... Question from my side is..... did Netgen successfully mesh the geometry you were trying to export into OpenFOAM? For the OpenFOAM export to work, you need to have the 3D Tet mesh too..... It does not work with just a 2D mesh. Also, you can only export linear elements.... if you asked Netgen to create second order elements, the export will not work. Hope this helps you come further :-)! Have a nice day! Philippose

May 25, 2011, 04:30		#3
almir New Member Join Date: May 2011 Location: Germany/Bosnia Posts: 9 Rep Power: 14	hi, now i have solved my problem. My geometry was to complicated, there were to many small curves. This curves have no influence flow, but for the programm there was to many to calculate, which i don´t need. greets