[Commercial meshers] FluentMeshToFoam no set written

kian · May 24, 2007, 18:14

Hi,
When I do
fluentMeshToFoam . cyl cylin.msh
I get this message at the end:

Default patch type set to empty
Checking mesh
Writing mesh
Only one cell group: no set written

End

where cylin.msh is a 2-D mesh, exported from Gambit for Fluent 5/6, and cyl is the icoFoam cavity case copied under a new directory.
I have tried a simple 3-D block as well, with no avail.
On the other hand, I've been able to do foamMeshToFluent successfully. However, the resulting .msh file is only recognized in Fluent and cannot be imported to Gambit. Please note that I don't want to export Foam mesh to Gambit, I only mentioned this, since it could help to find a remedy to the first issue.

I have searched the forums and haven't been able to locate an answer. Any advice is appreciated.

Kian

gschaider · May 25, 2007, 07:16

Hi Kian!

Your mesh has been written, so you can use it. "Only one cell group: no set written " means that in Gambit you 'only' defined one fluid zone and therefor no additional information was written. (You only need the additonal fluid zones for special applications)

kian · May 25, 2007, 12:04

Hello Bernhard,
Thank you for your reply. I was so convinced that there is no output! I am happy now

Vielen dank und schönes Wochenende

May 24, 2007, 18:14	FluentMeshToFoam no set written	#1
kian New Member Kian Mehravaran Join Date: Mar 2009 Location: London, U.K Posts: 22 Rep Power: 17	Hi, When I do fluentMeshToFoam . cyl cylin.msh I get this message at the end: Default patch type set to empty Checking mesh Writing mesh Only one cell group: no set written End where cylin.msh is a 2-D mesh, exported from Gambit for Fluent 5/6, and cyl is the icoFoam cavity case copied under a new directory. I have tried a simple 3-D block as well, with no avail. On the other hand, I've been able to do foamMeshToFluent successfully. However, the resulting .msh file is only recognized in Fluent and cannot be imported to Gambit. Please note that I don't want to export Foam mesh to Gambit, I only mentioned this, since it could help to find a remedy to the first issue. I have searched the forums and haven't been able to locate an answer. Any advice is appreciated. Kian

May 25, 2007, 07:16	Hi Kian! Your mesh has been	#2
gschaider Assistant Moderator Bernhard Gschaider Join Date: Mar 2009 Posts: 4,225 Rep Power: 51	Hi Kian! Your mesh has been written, so you can use it. "Only one cell group: no set written " means that in Gambit you 'only' defined one fluid zone and therefor no additional information was written. (You only need the additonal fluid zones for special applications) __________________ Note: I don't use "Friend"-feature on this forum out of principle. Ah. And by the way: I'm not on Facebook either. So don't be offended if I don't accept your invitation/friend request

May 25, 2007, 12:04	Hello Bernhard, Thank you for	#3
kian New Member Kian Mehravaran Join Date: Mar 2009 Location: London, U.K Posts: 22 Rep Power: 17	Hello Bernhard, Thank you for your reply. I was so convinced that there is no output! I am happy now Vielen dank und schönes Wochenende

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
does Hyperthreading affect the application of UDF?	SJSW	Fluent UDF and Scheme Programming	11	October 10, 2018 22:28
correction of Grub after installing Windows XP and 8	immortality	Lounge	20	January 5, 2014 17:41
Installation problems	indy	OpenFOAM Installation	7	April 3, 2009 09:40
OpenFOAM on MinGW crosscompiler hosted on Linux	allenzhao	OpenFOAM Installation	127	January 30, 2009 19:08
Problem installing on 64bit with ver13	jonititan	OpenFOAM Installation	0	April 28, 2006 05:45