|
[Sponsors] |
[waves2Foam] Questions about the overtopping utility |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
August 4, 2015, 07:30 |
Questions about the overtopping utility
|
#1 |
Member
Rafael Marques
Join Date: Mar 2014
Location: Almada/Mülheim a.d. Ruhr, Portugal/Germany
Posts: 67
Rep Power: 12 |
Hi Mr.Jacobsen
I am having a question about the overtopping utility, i want to ask what are the three values are they the vectors x,y,z? and what are the unity [m³/s/m]? i tried to read the source code but i am not familiar the C. Thanks again, Rafa Marques |
|
August 5, 2015, 03:01 |
|
#2 |
Senior Member
Niels Gjoel Jacobsen
Join Date: Mar 2009
Location: Copenhagen, Denmark
Posts: 1,900
Rep Power: 37 |
Good morning Rafael,
Could you please be a lot more specific of what you are referring to? There are a lot of places, where I can find a vector (x y z). Furthermore, I do not know, where you have found the unit [m^3/s/m], but it is a discharge per unit width. Kind regards, Niels
__________________
Please note that I do not use the Friend-feature, so do not be offended, if I do not accept a request. |
|
August 5, 2015, 05:49 |
|
#3 |
Member
Rafael Marques
Join Date: Mar 2014
Location: Almada/Mülheim a.d. Ruhr, Portugal/Germany
Posts: 67
Rep Power: 12 |
Hi Mr jacobsen,
Thanks for you reply and sorry for my impreciseness, when i use the overtopping functionObject, I obtain 3 values per timeStep (when using it with timeStep), and i don know what are this values (sorry about my ignorance) and thats my question? But i have more doubts, when i chose the faceZone i need to be sure that the phase passes through the faceZone completely? Greets Rafa Marques |
|
August 5, 2015, 13:39 |
|
#4 |
Senior Member
Niels Gjoel Jacobsen
Join Date: Mar 2009
Location: Copenhagen, Denmark
Posts: 1,900
Rep Power: 37 |
Good evening,
The vector is the directional overtopping (normal to the faceZone). I will not have access to the source for some days, but I think that the overtopping is given in m3/s. Concerning the second question, it makes little sense. The utility measures the flux of water over a given faceZone. That is it. Kind regards, Niels
__________________
Please note that I do not use the Friend-feature, so do not be offended, if I do not accept a request. |
|
August 5, 2015, 18:32 |
|
#5 |
Member
Rafael Marques
Join Date: Mar 2014
Location: Almada/Mülheim a.d. Ruhr, Portugal/Germany
Posts: 67
Rep Power: 12 |
Hi mr.Jacobsen
Thanks alto for the quick reply. What I mean is that, if I use a higher domain with the same overtopping a get a smallermassflow? Sorry I am asking because I not testedd it yet. Sometime I have difficulties to explain my problem sorry about that. Greets Rafa Marques |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
[Other] Contribution a new utility: refine wall layer mesh based on yPlus field | lakeat | OpenFOAM Community Contributions | 58 | December 23, 2021 02:36 |
wallHeatFlux Calculation wrt utility version | ahmet | OpenFOAM Post-Processing | 1 | December 18, 2016 19:45 |
[mesh manipulation] mirrorMesh utility preserving regions | zfaraday | OpenFOAM Meshing & Mesh Conversion | 1 | November 7, 2016 21:51 |
Something doens't work with wallHeatFlux utility or externalWallHeatFluxTemperat BC!! | zfaraday | OpenFOAM Post-Processing | 0 | February 5, 2015 16:47 |
Questions to utility yPlusLES | aylalisa | OpenFOAM Programming & Development | 9 | May 9, 2014 09:33 |