[OpenFOAM] foamToVTK and paraFoam show different results

akidess · October 28, 2010, 10:45

I've been using foamToVTK to post-process my data, and recently started playing around with Tecplot (using foamToTecplot360). To my surprise I was getting different velocity vectors in Tecplot and Paraview (3.8.1). I then tested paraFoam with paraview's integrated foam-reader (not the opencfd plugin), and the results were the same as using Tecplot (see below).

The geometry I'm plotting is an axisymmetric wedge, and the problems appear at the symmetry axis. Can anyone explain what foamToVTK is doing different than the native paraview reader?

7islands · October 28, 2010, 20:48

Hi Anton,
If the left edge is the axi-symmetric wedge, in this case I guess formToVTK is correct. Regarding the internal reader in ParaView the boundary value handling has been an issue as has been reported by another post. It's definitely in my to-do list but still take time as it is non-trivial.

Takuya

akidess · October 29, 2010, 05:36

Hi Takuya, thanks for your prompt response, and I appreciate you working on this.

The post you linked does look like exactly the same issue. But you are in good company, as the tecplot converter and also the sample utility don't seem to handle the wedge tip correctly. I'm in contact with the Tecplot support and hope to be able to resolve the issues there as well.

- Anton

October 28, 2010, 10:45	foamToVTK and paraFoam show different results	#1
akidess Senior Member Anton Kidess Join Date: May 2009 Location: Germany Posts: 1,377 Rep Power: 29	I've been using foamToVTK to post-process my data, and recently started playing around with Tecplot (using foamToTecplot360). To my surprise I was getting different velocity vectors in Tecplot and Paraview (3.8.1). I then tested paraFoam with paraview's integrated foam-reader (not the opencfd plugin), and the results were the same as using Tecplot (see below). The geometry I'm plotting is an axisymmetric wedge, and the problems appear at the symmetry axis. Can anyone explain what foamToVTK is doing different than the native paraview reader?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
foamToVTK will have a different values?! And the fvScheme questions.	wenxu	OpenFOAM Running, Solving & CFD	20	August 4, 2020 07:51
[OpenFOAM] Visualization problem on ParaFoam	Rider	ParaView	10	June 27, 2016 10:19
I can not see anything in paraFoam Please help	anmartin	OpenFOAM Installation	2	February 11, 2010 04:37
Kubuntu 8.10: paraFoam differences between 32 and 64 bit. Can you help me?	Xwang	OpenFOAM Installation	0	June 28, 2009 07:26
[OpenFOAM] FoamToVTK Animation with Paraview 3	podallaire	ParaView	5	October 9, 2007 07:26

October 28, 2010, 20:48		#2
7islands Super Moderator Takuya OSHIMA Join Date: Mar 2009 Location: Niigata City, Japan Posts: 518 Blog Entries: 1 Rep Power: 20	Hi Anton, If the left edge is the axi-symmetric wedge, in this case I guess formToVTK is correct. Regarding the internal reader in ParaView the boundary value handling has been an issue as has been reported by another post. It's definitely in my to-do list but still take time as it is non-trivial. Takuya

October 29, 2010, 05:36		#3
akidess Senior Member Anton Kidess Join Date: May 2009 Location: Germany Posts: 1,377 Rep Power: 29	Hi Takuya, thanks for your prompt response, and I appreciate you working on this. The post you linked does look like exactly the same issue. But you are in good company, as the tecplot converter and also the sample utility don't seem to handle the wedge tip correctly. I'm in contact with the Tecplot support and hope to be able to resolve the issues there as well. - Anton