boundary values

OFU · August 5, 2011, 05:10

Hello,

can anybody tell me where the boundary values in OpenFOAM are set? Are the specified in the middle of the boundary cells, in the middle of the surfaces or in the boundary points of the boundary cells or ....? And how can I set there the values for the pressure and the velocity?

Thanks,
Jennifer

m2montazari · August 5, 2011, 06:56

hi Jennifer,
I dont have enough info about that but I know that values are usually set at boundary faces not cells. however I dont know values are set in boundary nodes or at the middle of boundary faces? I read in a paper that openfoam is cell-based solver. if this is true, values should be set in boundary face centres.
cheers,

bigbang · August 8, 2011, 14:37

I am new to openFOAM, but I just wrote a program with some borrowed code from the forum to set up non uniform boundary values.

It is my understanding that the value is stored at the center of each cell face.

Hope this helps.

OFU · August 9, 2011, 03:43

Hi,

thanks for your answers, bigbang and m2montazari.

Bigband, is there a possibilty to get the code you wrote from you?

Jennifer

bigbang · August 9, 2011, 06:27

The thread where I got the code and then troubleshooted it for openfoam 2.0.0 is here:

http://www.cfd-online.com/Forums/ope...tml#post319363

Good luck

August 5, 2011, 05:10	boundary values	#1
OFU New Member Jennifer Join Date: Aug 2009 Location: Germany Posts: 28 Rep Power: 16	Hello, can anybody tell me where the boundary values in OpenFOAM are set? Are the specified in the middle of the boundary cells, in the middle of the surfaces or in the boundary points of the boundary cells or ....? And how can I set there the values for the pressure and the velocity? Thanks, Jennifer

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
mesh file for flow over a circular cylinder	Ardalan	Main CFD Forum	7	December 15, 2020 13:06
error when calculating values at boundary using refCast	prabhu	OpenFOAM	7	March 12, 2018 08:31
inlet velocity boundary condition	murali	CFX	5	August 3, 2012 08:56
Creating Face in CFD Post and export Values as Boundary Conditions	flow87	CFX	2	June 4, 2011 04:06
Turbulence boundary values	lego	Main CFD Forum	0	October 24, 2002 13:47

August 5, 2011, 06:56		#2
m2montazari Senior Member Mohammad Join Date: Feb 2010 Location: Shiraz, Iran Posts: 108 Rep Power: 16	hi Jennifer, I dont have enough info about that but I know that values are usually set at boundary faces not cells. however I dont know values are set in boundary nodes or at the middle of boundary faces? I read in a paper that openfoam is cell-based solver. if this is true, values should be set in boundary face centres. cheers,

August 8, 2011, 14:37		#3
bigbang Member Alex Join Date: Jun 2010 Location: Planet Earth Posts: 43 Rep Power: 15	I am new to openFOAM, but I just wrote a program with some borrowed code from the forum to set up non uniform boundary values. It is my understanding that the value is stored at the center of each cell face. Hope this helps.

August 9, 2011, 03:43		#4
OFU New Member Jennifer Join Date: Aug 2009 Location: Germany Posts: 28 Rep Power: 16	Hi, thanks for your answers, bigbang and m2montazari. Bigband, is there a possibilty to get the code you wrote from you? Jennifer

August 9, 2011, 06:27		#5
bigbang Member Alex Join Date: Jun 2010 Location: Planet Earth Posts: 43 Rep Power: 15	The thread where I got the code and then troubleshooted it for openfoam 2.0.0 is here: http://www.cfd-online.com/Forums/ope...tml#post319363 Good luck