How to simulate flows around ships with GGI

slint · June 2, 2012, 13:30

Hello,

I want to simulate flows around a ship for several wind directions with OpenFOAM. So I have to rotate the ship or the domain for that job. We did that in CFX with two independent meshes (the ship is placed in a cylinder, the domain rotates around the cylinder) and the GGI Interface. I know that GGI is also available in OpenFOAM, but I don't know how to implement this function.

Is there anybody, who can give me some basic information about the implementation of GGI interface? I found some tutorials about turbomachinery, but this was not useful...

I appreciate every good advice, thanks.

maHein · June 5, 2012, 10:21

hi slint,

you could start with the ERCOFTAC centrifugal pump test cases. In one case, the inner mesh is rotating while the outer is fixed.

If you are using OpenFOAM 2.1, you could start with the propeller tutorial (incompressible/pimpleDyMFoam/propeller I think). Again, one rotating inner mesh and a fixed outer mesh coupled by an interface (cyclicAMI - similar to GGI in OpenFOAM 1.6ext).

martin

slint · June 13, 2012, 12:59

hi martin,

thanks for your advice. After some trail and error, AMI seems to work well

Robert

June 2, 2012, 13:30	How to simulate flows around ships with GGI	#1
slint New Member Join Date: Jan 2012 Posts: 10 Rep Power: 14	Hello, I want to simulate flows around a ship for several wind directions with OpenFOAM. So I have to rotate the ship or the domain for that job. We did that in CFX with two independent meshes (the ship is placed in a cylinder, the domain rotates around the cylinder) and the GGI Interface. I know that GGI is also available in OpenFOAM, but I don't know how to implement this function. Is there anybody, who can give me some basic information about the implementation of GGI interface? I found some tutorials about turbomachinery, but this was not useful... I appreciate every good advice, thanks. Last edited by slint; June 2, 2012 at 19:42.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Simulate the wind profile on a wind turbine---> HOW ????	mohammad	Main CFD Forum	0	April 13, 2012 08:07
alternative method for ggi	wWieWalter	OpenFOAM	1	September 20, 2011 08:18
Rotating cylinder with GGI	lbeaudet	OpenFOAM Running, Solving & CFD	4	July 6, 2009 02:13
plastic flows	carno	Siemens	2	November 13, 2003 12:31
Modeling Free Surface Flows	Elliot Schwartz	Main CFD Forum	5	August 25, 1998 21:03

June 5, 2012, 10:21		#2
maHein Member Join Date: Jun 2012 Posts: 76 Rep Power: 13	hi slint, you could start with the ERCOFTAC centrifugal pump test cases. In one case, the inner mesh is rotating while the outer is fixed. If you are using OpenFOAM 2.1, you could start with the propeller tutorial (incompressible/pimpleDyMFoam/propeller I think). Again, one rotating inner mesh and a fixed outer mesh coupled by an interface (cyclicAMI - similar to GGI in OpenFOAM 1.6ext). martin

June 13, 2012, 12:59		#3
slint New Member Join Date: Jan 2012 Posts: 10 Rep Power: 14	hi martin, thanks for your advice. After some trail and error, AMI seems to work well Robert