|
[Sponsors] |
Error caused by defining a Ramp BC for a parameter |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
February 24, 2014, 01:14 |
Error caused by defining a Ramp BC for a parameter
|
#1 |
Senior Member
Bobby
Join Date: Oct 2012
Location: Michigan
Posts: 454
Rep Power: 15 |
Dear Foamres
I have defined a ramp BC for a parameter to increase from 0 in the start to 2 in the end of simulation (0.15 sec) Code:
Cchi ( (0 0) (0.15 2) ); Code:
Courant Number mean: 0.0187511 max: 0.307637 deltaT = 2.20033e-05 Time = 0.113157 diagonal: Solving for rho, Initial residual = 0, Final residual = 0, No Iterations 0 DILUPBiCG: Solving for Ux, Initial residual = 3.29237e-05, Final residual = 3.19744e-12, No Iterations 2 DILUPBiCG: Solving for Uy, Initial residual = 0.0056262, Final residual = 1.44868e-12, No Iterations 3 DILUPBiCG: Solving for Uz, Initial residual = 0.000508302, Final residual = 1.91713e-11, No Iterations 2 DILUPBiCG: Solving for Z, Initial residual = 3.85859e-06, Final residual = 4.80055e-10, No Iterations 1 Correcting mixture fraction variance with CvarZ = 1 Correcting scalar dissipation rate with Cchi = 1.50876 #0 Foam::error::printStack(Foam::Ostream&) in "/home/babak/OpenFOAM/OpenFOAM-2.1.x/platforms/linux64GccDPOpt/lib/libOpenFOAM.so" #1 Foam::sigSegv::sigHandler(int) in "/home/babak/OpenFOAM/OpenFOAM-2.1.x/platforms/linux64GccDPOpt/lib/libOpenFOAM.so" #2 in "/lib/x86_64-linux-gnu/libc.so.6" #3 Foam::linearInterpolation::interpolate(Foam::List<int> const&, Foam::List<double> const&) const in "/home/babak/OpenFOAM/babak-2.1.x/platforms/linux64GccDPOpt/lib/libFlameletCombustionModels.so" #4 Foam::combustionModels::YSLFModel<Foam::combustionModels::rhoCombustionModel, Foam::sutherlandTransport<Foam::specieThermo<Foam::janafThermo<Foam::perfectGas> > > >::correct() in "/home/babak/OpenFOAM/babak-2.1.x/platforms/linux64GccDPOpt/lib/libFlameletCombustionModels.so" #5 in "/home/babak/OpenFOAM/babak-2.1.x/platforms/linux64GccDPOpt/bin/flameletFoam" #6 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #7 in "/home/babak/OpenFOAM/babak-2.1.x/platforms/linux64GccDPOpt/bin/flameletFoam" Segmentation fault Regards Bobi |
|
February 24, 2014, 06:38 |
|
#2 |
Senior Member
Joachim Herb
Join Date: Sep 2010
Posts: 650
Rep Power: 21 |
In $FOAM_TUTORIALS/multiphase/interPhaseChangeDyMFoam/propeller/0.org/U there is an example of a time depending boundary condition defined by a table.
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Question about defining parameter in CFX-pre | Anna Tian | CFX | 1 | September 30, 2012 11:10 |
Force can not converge | colopolo | CFX | 13 | October 4, 2011 22:03 |
Error when input new parameter in Fluent | micro11sl | FLUENT | 0 | July 1, 2011 06:42 |
Defining a parameter for UDF | Philipp_Sch | Fluent UDF and Scheme Programming | 11 | May 2, 2011 22:32 |
compile errors of boundary condition "expDirectionMixed" | liying02ts | OpenFOAM Bugs | 2 | February 1, 2010 20:11 |