|
[Sponsors] |
rhoSimpleFoam :: Maximum number of iterations exceeded |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
April 8, 2014, 08:18 |
rhoSimpleFoam :: Maximum number of iterations exceeded
|
#1 | |
Member
|
Hi all,
I am trying to solve a case with time varying Boundary conditions using uniformValue and rhoSimpleFoam. The input given for patches in p and T is in tabular form while the U is set as 'pressureInletVelocity' It is solving upto 2 clock time while afterwards it says Quote:
http://www.cfd-online.com/Forums/ope...implefoam.html http://www.cfd-online.com/Forums/ope...-exceeded.html http://www.cfd-online.com/Forums/ope...implefoam.html but got the same results. Now I changed the solver for 'p' from GAMG to DICPCG and next time to PCG (because I think that the problem is with 'p' only). and still the same thing. Please help me ASAP... Thanks and Regards, Adarsh Tiwari |
||
April 12, 2014, 01:56 |
|
#2 |
Member
Vojtech Betak
Join Date: Mar 2009
Location: Czech republic
Posts: 33
Rep Power: 18 |
Dear Adarsh,
rhoSimpleFoam is a steady-state solver. If you want use time varying boundary condition try to use rhoPimpleFoam |
|
April 14, 2014, 01:32 |
|
#3 |
Member
|
Greetings Betakv,
I have already simulated using rhoPimpleFoam but I got some fancy results, with best of my knowledge I can say that the probability of getting appropriate results is much more higher in rhoSimpleFoam. It would be great help if you provide me some tutorials about rhoSimpleFoam, I already have one, but it is not worth about this case. Thanks and Regards, Adarsh Tiwari |
|
April 14, 2014, 02:00 |
|
#4 |
Member
Vojtech Betak
Join Date: Mar 2009
Location: Czech republic
Posts: 33
Rep Power: 18 |
Dear Adarsh,
there are number of reasons( boundary/initial condition, solver setting, ... ) why you got fancy results. Can you send description of your case? |
|
April 16, 2014, 03:20 |
|
#5 |
Member
|
Greeting Betakv,
sorry for late reply. The file is too large to upload hence i am attaching the brief version of the same but by removing some of the data-table entries. In pressure files I have also tried with the uniformTotalPressure but still got nothing in solution schemes also i have changed form GAMG to different solver. I have also tried with faceCente and cellCenter schemes. Thanks and Regards, Adarsh Tiwari |
|
April 16, 2014, 04:47 |
|
#6 | |
Member
Vojtech Betak
Join Date: Mar 2009
Location: Czech republic
Posts: 33
Rep Power: 18 |
Dear Adarsh,
you have quite lot of errors in boundary condition especially on the inlet and outlet. On the inlet you have to prescribe a totalPressure bc for pressure. On the outlet you have to prescribe zeroGradient or inletOutlet bc for velocity and temperature betakv Quote:
|
||
April 22, 2014, 07:49 |
|
#7 |
Member
|
hi Betakv,
As I already informed you that the p and T boundary conditions are fixed, only thing I can play with is U. I used zeroGradient and inletOutlet bc for velocity with different combinations but still getting the same message out. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Foam::error::PrintStack | almir | OpenFOAM Running, Solving & CFD | 91 | December 21, 2022 04:50 |
buoyantSimpleFoam and watertank | Tobi | OpenFOAM Running, Solving & CFD | 100 | December 18, 2022 08:15 |
Floating point exception error | Alan | OpenFOAM Running, Solving & CFD | 11 | July 1, 2021 21:51 |
Help for the small implementation in turbulence model | shipman | OpenFOAM Programming & Development | 25 | March 19, 2014 10:08 |
calculation stops after few time steps | sivakumar | OpenFOAM Running, Solving & CFD | 7 | March 17, 2013 06:37 |