Hello FOAMERS, I am running a
 

Hello FOAMERS,
I am running a les-VOF simulation of a liquid jet of 200 bar injected into a chamber. I have been provided with the set up files which were sucessfully used to run such simulations in OF 1.4. But when I use the same set up files to run on OF 1.5. It gave me the following errors:

1. gammaCompression 1.0 , this scheme is not identified and OpenFOAM gave me a list of schemes available to solve the gamma equation, since I could not find the scheme gammaCompression 1.0 in the list, I chose interfaceCompression to solve the gamma equation.

2. Then when i tried to run the solver after this change, it solves the velocity equations for the 0 time step, but while starting to solve the pressure equation it gives me a error message as pated below:

Create mesh for time = 0


Reading environmentalProperties
Reading field pd

Reading field gamma

Reading field U

Reading/calculating face flux field phi

Reading transportProperties

Selecting incompressible transport model Newtonian
Selecting incompressible transport model Newtonian
Calculating field g.h

Selecting LES turbulence model oneEqEddy
time step continuity errors : sum local = 0, global = 0, cumulative = 0
DICPCG: Solving for pcorr, Initial residual = 0, Final residual = 0, No Iterations 0
time step continuity errors : sum local = 0, global = 0, cumulative = 0
Courant Number mean: 0 max: 0

Starting time loop

Courant Number mean: 0 max: 0
deltaT = 1.1904762e-08
Time = 1.19047619e-08

MULES: Solving for gamma
Liquid phase volume fraction = 0.00033350008 Min(gamma) = 0 Max(gamma) = 1
MULES: Solving for gamma
Liquid phase volume fraction = 0.00033350008 Min(gamma) = 0 Max(gamma) = 1
MULES: Solving for gamma
Liquid phase volume fraction = 0.00033350008 Min(gamma) = 0 Max(gamma) = 1
MULES: Solving for gamma
Liquid phase volume fraction = 0.00033350008 Min(gamma) = 0 Max(gamma) = 1
DILUPBiCG: Solving for k, Initial residual = 1, Final residual = 1.1917548e-15, No Iterations 2
bounding k, min: 0 max: 100 average: 1.2078798e-06
DILUPBiCG: Solving for Ux, Initial residual = 0, Final residual = 0, No Iterations 0
DILUPBiCG: Solving for Uy, Initial residual = 1, Final residual = 4.882832e-13, No Iterations 2
DILUPBiCG: Solving for Uz, Initial residual = 0, Final residual = 0, No Iterations 0
DICPCG: Solving for pd, Initial residual = 1, Final residual = 0.034418455, No Iterations 1001


keyword pdFinal is undefined in dictionary "/home/kumar/OpenFOAM/kumar-1.5/run/test/Offset100um_200into10bar/system/fvSolut ion::solvers"

file: /home/kumar/OpenFOAM/kumar-1.5/run/test/Offset100um_200into10bar/system/fvSoluti on::solvers from line 27 to line 32.

From function dictionary::lookupEntry(const word& keyword) const
in file db/dictionary/dictionary.C at line 213.

FOAM exiting


I can see that there is no definition of Pd in the fvSolution file.
But the same setting worked for OF-1.4. so is there any major change in OF-1.5 in solving the pressure equation.

Any comments are welcome

with regards
K.Suresh kumar