movingCone without stretching the mesh

anon_c · July 19, 2009, 09:04

hello

is it posible to move the cone without strtching the mesh

with the posiblity of

Cell layer additional-removal interface

how could i reals this

and is it posible to change the speed of the motion of the cone (with timedependent motion)

timedependent form the flowtime??

Form:
init the first 2 pic and the last to pic are the end

anon_c · July 19, 2009, 09:16

soory! here are the next tow pic

henrik · July 20, 2009, 04:21

Dear Tajoooko,

have a look at the following tutorial in 1.5-ext

$FOAM_TUT/tutorials/icoDyMFoam/movingConeTopo

Have a look here for how to obtain 1.5-ext

http://openfoamwiki.net/index.php/Ho...M_the_easy_way

and other post on the forum.

Henrik

anon_c · July 20, 2009, 04:40

hello the

movingConeTopo

is not in the tutorials i instaled the openfoam-1.5 but there is this tutoral not icluded

henrik · July 20, 2009, 05:37

Dear Tajoooko,

you need 1.5-extend, not the 1.5 (plain, vanilla) or 1.5.x (patched vanilla, git) version, because what you want to do requires topological mesh changes.

http://www.cfd-online.com/Forums/ope...x-1-5-dev.html

Henrik

anon_c · July 20, 2009, 07:30

ok thank you very much danke dir

now i am downloding the extended about 800MB

but i dont found an install document, to install it like an extende (erweiterung) to the openfoam

henrik · July 20, 2009, 07:46

Dear Tajoooko,

you are probably downloading the OpenFOAM on SLAX tar-ball which is a full operating system to put on a USB stick. It's probably not what you want, but it's very nice for beginners. Instructions are here:

http://www.cfd-online.com/Forums/ope...lax-based.html

If you are aiming for the "normal" OF-1.5-ext installation. Follow the link in my first post. There is no binary pack, so you must compile from source.

Henrik

anon_c · July 20, 2009, 10:35

i downloaded this and burn a cd

OpenFOAM_SLAX_noDebug.iso

and now how should i install openfoam from this iso cd???

henrik · July 20, 2009, 10:44

No, put it into the drive and reboot, but make sure the boot order picks up the CD first.

Henrik

anon_c · July 20, 2009, 11:01

ok i do that, and that is not an alternativ

i need the real openfoam-1.5-dev i will try to do that but it seems to be more difficult that the normal openfoam i get the normal openfoam quickly installed but this version is making some problemes

i would wirte here again

anon_c · July 21, 2009, 09:41

hello

i download

openfaom-1.5-dev and the other tgtz files form the openfoam webside

then i rename openfoam1.5-de to openfoam 1.5 and unpake the tgtz files

then i remane openfoam1.5 to openfoam 1.5-dev

then i unpake the tgtz of thirdparty and

do update my ~/.bashrc

then .$HOME/.bashrc

after that i do the installation test from openfaoam and every thing was ok

the icofoam solver and the blockMesh all was there (i just typ it in the bash)

after that i cd in the openfoam-1.5-dev and typ ./Allwmake this takes alout of time about 2 or 3 hours

and then every think was fisched

but the problem now the path dont work any more

i canot typ blockMesh or something other there is nothing more i have do cd in the directory ob bin and take them from there

what is worng??

henrik · July 21, 2009, 09:55

Dear Tajoooko,

Start a fresh shell and run foamInstallationTest. If it cannot be found, check your environment settings until you it's picked up.

Henrik

anon_c · July 21, 2009, 10:04

ammar@ammar-laptop:~$ foamInstallationTest
Executing /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/bin/foamInstallationTest:

Checking basic setup...
-------------------------------------------------------------------------------
Shell: bash
Host: ammar-laptop
OS: Linux version 2.6.27-14-generic
-------------------------------------------------------------------------------

Checking main OpenFOAM env variables...
-------------------------------------------------------------------------------
Environment_variable Set_to_file_or_directory Valid Crit
-------------------------------------------------------------------------------
$WM_PROJECT_INST_DIR /home/ammar/OpenFOAM yes yes
$WM_PROJECT_USER_DIR /home/ammar/OpenFOAM/ammar-1.5-dev yes no
$WM_THIRD_PARTY_DIR /home/ammar/OpenFOAM/ThirdParty yes yes
-------------------------------------------------------------------------------

Checking the OpenFOAM env variables set on the PATH...
-------------------------------------------------------------------------------
Environment_variable Set_to_file_or_directory Valid Path Crit
-------------------------------------------------------------------------------
$WM_PROJECT_DIR /home/ammar/OpenFOAM/OpenFOAM-1.5-dev yes yes yes

$FOAM_APPBIN ...5-dev/applications/bin/linuxGccDPOpt yes yes yes
$FOAM_USER_APPBIN ...5-dev/applications/bin/linuxGccDPOpt yes yes no
$WM_DIR ...mmar/OpenFOAM/OpenFOAM-1.5-dev/wmake yes yes yes
-------------------------------------------------------------------------------

Checking the OpenFOAM env variables set on the LD_LIBRARY_PATH...
-------------------------------------------------------------------------------
Environment_variable Set_to_file_or_directory Valid Path Crit
-------------------------------------------------------------------------------
$FOAM_LIBBIN ...M/OpenFOAM-1.5-dev/lib/linuxGccDPOpt yes yes yes
$FOAM_USER_LIBBIN ...FOAM/ammar-1.5-dev/lib/linuxGccDPOpt yes yes no
$MPI_ARCH_PATH ...penmpi-1.2.6/platforms/linuxGccDPOpt yes yes yes
-------------------------------------------------------------------------------

Third party software
-------------------------------------------------------------------------------
Software Version Location
-------------------------------------------------------------------------------
WARNING: gcc version does not match gcc supplied with this release of OpenFOAM
Supplied version: 4.3.1
User version : ../src/configure
Minimum required: 4.2.0

gcc ...figure
WARNING: Conflicting installations:
OpenFOAM settings : /bin/gcc
current path : /usr/bin/gcc
CRITICAL ERROR

gzip 1.3.12 /bin/gzip
tar 1.20 /bin/tar
icoFoam
WARNING: Conflicting installations:
OpenFOAM settings : /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/applications/bin/linuxGccDPOpt/icoFoam
current path :
CRITICAL ERROR

-------------------------------------------------------------------------------

Checking networking...
-------------------------------------------------------------------------------
Action Result Crit
-------------------------------------------------------------------------------
Pinging_ammar-laptop Successful yes
Pinging_localHost Successful yes
Test_rsh: Unsuccessful_connection_refused* yes
Test_ssh: Successful yes
(*) Only one of rsh or ssh is required by the OpenFOAM enviroment.

-------------------------------------------------------------------------------

Base configuration ok.

The foam installation contains 2 critical error(s).

Review the output for warning messages and consult
the installation guide for trouble shooting.

done.

henrik · July 21, 2009, 10:24

Dear Ammar,

The problem is here:

icoFoam
WARNING: Conflicting installations:
OpenFOAM settings : /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/applications/bin/linuxGccDPOpt/icoFoam

I think you might have two OF installations in you PATH ...

Henrik

anon_c · July 21, 2009, 11:14

yeh that could be wirte bcz i tryed it with the build surce form debian but it was not good and then i thougt i geet it uninstalled

with

sudo apt-get --purge remove openfoam-dev-1.5

and then i first do install that again

but it could also be a gcc problem bcz i installed it also tow times, is there a posibility to get that problem out ?

henrik · July 21, 2009, 13:03

Dear Ammar,

sorry, but it seems to me that you are not taking advice and trying out alternative routes. I don't care if want to you waste your time, but I do object to wasting mine.

Please remove all those clever OF binary packages that make you life difficult. However, keep the vanilla OF 1.5 that you picked up from OpenCFD as a fall-back and in case you have trouble compiling paraFoam.

Go to the directory with the OpenFOAM-1.5 and ThirdParty directories (cd $FOAM_INST_DIR) and pull the latest OF-ext:

Code:

svn co 
https://openfoam-extend.svn.sourceforge.net/svnroot/openfoam-extend/trunk/Core/OpenFOAM-1.5-dev

Then pick this up with your environment, open a fresh shell, cd $FOAM_SRC, ./Allwmake, open another fresh shell, foamInstallationTest

@GCC: Anything > 4.2.0 will be fine as long it's compatible with your system.

Henrik

anon_c · July 22, 2009, 02:42

I do it again on another way and now it works very fine

so dont be warry

and thank you very very much (danke dir sehr)

i would wirte a how to install openfoam on ubuntu 8.10 and i would wirte how to install the paraview form the apt/synaptic to geht the newist one without a problem and by one klick

July 20, 2009, 04:21		#3
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Tajoooko, have a look at the following tutorial in 1.5-ext $FOAM_TUT/tutorials/icoDyMFoam/movingConeTopo Have a look here for how to obtain 1.5-ext http://openfoamwiki.net/index.php/Ho...M_the_easy_way and other post on the forum. Henrik Last edited by henrik; July 20, 2009 at 05:26.

July 21, 2009, 13:03		#16
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Ammar, sorry, but it seems to me that you are not taking advice and trying out alternative routes. I don't care if want to you waste your time, but I do object to wasting mine. Please remove all those clever OF binary packages that make you life difficult. However, keep the vanilla OF 1.5 that you picked up from OpenCFD as a fall-back and in case you have trouble compiling paraFoam. Go to the directory with the OpenFOAM-1.5 and ThirdParty directories (cd $FOAM_INST_DIR) and pull the latest OF-ext: Code: svn co https://openfoam-extend.svn.sourceforge.net/svnroot/openfoam-extend/trunk/Core/OpenFOAM-1.5-dev Then pick this up with your environment, open a fresh shell, cd $FOAM_SRC, ./Allwmake, open another fresh shell, foamInstallationTest @GCC: Anything > 4.2.0 will be fine as long it's compatible with your system. Henrik

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dynamic Mesh Problem.	Tom Clark	FLUENT	10	June 21, 2021 04:27
virtual geometry	richard	FLUENT	4	January 7, 2009 05:16
how to extend FSI 2D codes to 3D, need advises	abouziar	Main CFD Forum	1	May 30, 2008 04:08
basic of mesh refinement	arya	CFX	4	June 19, 2007 12:21
General questions on grid-based computing	Adrin Gharakhani	Main CFD Forum	21	June 5, 2000 13:47

July 20, 2009, 04:40		#4
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	hello the movingConeTopo is not in the tutorials i instaled the openfoam-1.5 but there is this tutoral not icluded

July 20, 2009, 05:37		#5
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Tajoooko, you need 1.5-extend, not the 1.5 (plain, vanilla) or 1.5.x (patched vanilla, git) version, because what you want to do requires topological mesh changes. http://www.cfd-online.com/Forums/ope...x-1-5-dev.html Henrik

July 20, 2009, 07:30		#6
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	ok thank you very much danke dir now i am downloding the extended about 800MB but i dont found an install document, to install it like an extende (erweiterung) to the openfoam

July 20, 2009, 07:46		#7
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Tajoooko, you are probably downloading the OpenFOAM on SLAX tar-ball which is a full operating system to put on a USB stick. It's probably not what you want, but it's very nice for beginners. Instructions are here: http://www.cfd-online.com/Forums/ope...lax-based.html If you are aiming for the "normal" OF-1.5-ext installation. Follow the link in my first post. There is no binary pack, so you must compile from source. Henrik

July 20, 2009, 10:35		#8
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	i downloaded this and burn a cd OpenFOAM_SLAX_noDebug.iso and now how should i install openfoam from this iso cd???

July 20, 2009, 10:44		#9
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	No, put it into the drive and reboot, but make sure the boot order picks up the CD first. Henrik

July 20, 2009, 11:01		#10
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	ok i do that, and that is not an alternativ i need the real openfoam-1.5-dev i will try to do that but it seems to be more difficult that the normal openfoam i get the normal openfoam quickly installed but this version is making some problemes i would wirte here again

July 21, 2009, 09:41		#11
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	hello i download openfaom-1.5-dev and the other tgtz files form the openfoam webside then i rename openfoam1.5-de to openfoam 1.5 and unpake the tgtz files then i remane openfoam1.5 to openfoam 1.5-dev then i unpake the tgtz of thirdparty and do update my ~/.bashrc then .$HOME/.bashrc after that i do the installation test from openfaoam and every thing was ok the icofoam solver and the blockMesh all was there (i just typ it in the bash) after that i cd in the openfoam-1.5-dev and typ ./Allwmake this takes alout of time about 2 or 3 hours and then every think was fisched but the problem now the path dont work any more i canot typ blockMesh or something other there is nothing more i have do cd in the directory ob bin and take them from there what is worng??

July 21, 2009, 09:55		#12
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Tajoooko, Start a fresh shell and run foamInstallationTest. If it cannot be found, check your environment settings until you it's picked up. Henrik

July 21, 2009, 10:04		#13
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	ammar@ammar-laptop:~$ foamInstallationTest Executing /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/bin/foamInstallationTest: Checking basic setup... ------------------------------------------------------------------------------- Shell: bash Host: ammar-laptop OS: Linux version 2.6.27-14-generic ------------------------------------------------------------------------------- Checking main OpenFOAM env variables... ------------------------------------------------------------------------------- Environment_variable Set_to_file_or_directory Valid Crit ------------------------------------------------------------------------------- $WM_PROJECT_INST_DIR /home/ammar/OpenFOAM yes yes $WM_PROJECT_USER_DIR /home/ammar/OpenFOAM/ammar-1.5-dev yes no $WM_THIRD_PARTY_DIR /home/ammar/OpenFOAM/ThirdParty yes yes ------------------------------------------------------------------------------- Checking the OpenFOAM env variables set on the PATH... ------------------------------------------------------------------------------- Environment_variable Set_to_file_or_directory Valid Path Crit ------------------------------------------------------------------------------- $WM_PROJECT_DIR /home/ammar/OpenFOAM/OpenFOAM-1.5-dev yes yes yes $FOAM_APPBIN ...5-dev/applications/bin/linuxGccDPOpt yes yes yes $FOAM_USER_APPBIN ...5-dev/applications/bin/linuxGccDPOpt yes yes no $WM_DIR ...mmar/OpenFOAM/OpenFOAM-1.5-dev/wmake yes yes yes ------------------------------------------------------------------------------- Checking the OpenFOAM env variables set on the LD_LIBRARY_PATH... ------------------------------------------------------------------------------- Environment_variable Set_to_file_or_directory Valid Path Crit ------------------------------------------------------------------------------- $FOAM_LIBBIN ...M/OpenFOAM-1.5-dev/lib/linuxGccDPOpt yes yes yes $FOAM_USER_LIBBIN ...FOAM/ammar-1.5-dev/lib/linuxGccDPOpt yes yes no $MPI_ARCH_PATH ...penmpi-1.2.6/platforms/linuxGccDPOpt yes yes yes ------------------------------------------------------------------------------- Third party software ------------------------------------------------------------------------------- Software Version Location ------------------------------------------------------------------------------- WARNING: gcc version does not match gcc supplied with this release of OpenFOAM Supplied version: 4.3.1 User version : ../src/configure Minimum required: 4.2.0 gcc ...figure WARNING: Conflicting installations: OpenFOAM settings : /bin/gcc current path : /usr/bin/gcc CRITICAL ERROR gzip 1.3.12 /bin/gzip tar 1.20 /bin/tar icoFoam WARNING: Conflicting installations: OpenFOAM settings : /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/applications/bin/linuxGccDPOpt/icoFoam current path : CRITICAL ERROR ------------------------------------------------------------------------------- Checking networking... ------------------------------------------------------------------------------- Action Result Crit ------------------------------------------------------------------------------- Pinging_ammar-laptop Successful yes Pinging_localHost Successful yes Test_rsh: Unsuccessful_connection_refused* yes Test_ssh: Successful yes (*) Only one of rsh or ssh is required by the OpenFOAM enviroment. ------------------------------------------------------------------------------- Base configuration ok. The foam installation contains 2 critical error(s). Review the output for warning messages and consult the installation guide for trouble shooting. done.

July 21, 2009, 10:24		#14
henrik Senior Member Henrik Rusche Join Date: Mar 2009 Location: Wernigerode, Sachsen-Anhalt, Germany Posts: 281 Rep Power: 18	Dear Ammar, The problem is here: icoFoam WARNING: Conflicting installations: OpenFOAM settings : /home/ammar/OpenFOAM/OpenFOAM-1.5-dev/applications/bin/linuxGccDPOpt/icoFoam I think you might have two OF installations in you PATH ... Henrik

July 21, 2009, 11:14		#15
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	yeh that could be wirte bcz i tryed it with the build surce form debian but it was not good and then i thougt i geet it uninstalled with sudo apt-get --purge remove openfoam-dev-1.5 and then i first do install that again but it could also be a gcc problem bcz i installed it also tow times, is there a posibility to get that problem out ?

July 22, 2009, 02:42		#17
anon_c Disabled Join Date: Jul 2009 Posts: 63 Rep Power: 16	I do it again on another way and now it works very fine so dont be warry and thank you very very much (danke dir sehr) i would wirte a how to install openfoam on ubuntu 8.10 and i would wirte how to install the paraview form the apt/synaptic to geht the newist one without a problem and by one klick