[snappyHexMesh] SnappyHexMesh Meshing inside a cylinder

nammari · March 10, 2011, 13:32

Good evening Foamers,
I was wondering if anyone could help, I am trying to model a tank in simple domain. I am trying to analyse the recirculations zones inside the cylinder and outside.

So far it has been straight forwards to create a solid cylinder, but creating a hollow cylinder using snappyhexmesh seems a wee bit tricky, I haven't managed so far, does anyone have any ideas ? Much appreciated

Dia

FG_HSRM · March 11, 2011, 07:25

Hi Dia,
Maybe, you can give more details about your geometry, like is the inside domain connected with the outside domain?
It also would help to make clear, which procedure you are using.
Regards, fritz

nammari · March 11, 2011, 09:46

Hi Fritz,
Thanks for answering back, that is what I want indeed that the inside domain is connected to the outside domain. Such that I would allow the "wind" to wizz inside the the tank( storage tank) and outside it.

If you don't mind what do you mean by procedure ? I am planning to test out a few solvers, and play around with windfoam.

As you can get I am trying to avoid "creating" the blockMesh dict by hand, or trying to use other software to create the geometry.
Cheers
Dia

FG_HSRM · March 11, 2011, 10:48

Quote:

Originally Posted by nammari

If you don't mind what do you mean by procedure ? I am planning to test out a few solvers, and play around with windfoam.

As you can get I am trying to avoid "creating" the blockMesh dict by hand, or trying to use other software to create the geometry.

The geometry import is exactly what I meant with procedure, sorry for my unclear question. Until now, I just can say that you have to make sure in the snappyHEXMeshDict that the "locationInMesh" is carefully placed and there shouldn't be a boundary between the two parts of the domain.

Besides, what exactly is the problem?

nammari · March 11, 2011, 14:10

I was trying to create a hollow cylinder with the opening into the domain. So far the cylinders or objects I create are closed. That is my issue. Not how to do that.
Cheers
Dia

FG_HSRM · March 11, 2011, 19:49

Then, I don't understand your problem. It's absolutely the same.

March 10, 2011, 13:32	SnappyHexMesh Meshing inside a cylinder	#1
nammari New Member Diauddin Nammari Join Date: Mar 2009 Posts: 8 Rep Power: 17	Good evening Foamers, I was wondering if anyone could help, I am trying to model a tank in simple domain. I am trying to analyse the recirculations zones inside the cylinder and outside. So far it has been straight forwards to create a solid cylinder, but creating a hollow cylinder using snappyhexmesh seems a wee bit tricky, I haven't managed so far, does anyone have any ideas ? Much appreciated Dia

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] Problems with scaling meshes when meshing with SnappyHexmesh	Bnitter	OpenFOAM Meshing & Mesh Conversion	1	November 15, 2018 08:26
[Gmsh] 3D Free surface flow past circular cylinder meshing using GMSH	arieljeds	OpenFOAM Meshing & Mesh Conversion	7	January 14, 2017 12:57
[snappyHexMesh] Inside and outside mesh with snappyhexmesh	nzy102	OpenFOAM Meshing & Mesh Conversion	21	February 16, 2016 16:42
simulation of piston motion inside a hydraulic cylinder	mosman	FLUENT	0	August 6, 2011 15:44
2D planar cylinder meshing problem	saisanthoshm88	ANSYS Meshing & Geometry	15	December 27, 2010 11:14

March 11, 2011, 07:25		#2
FG_HSRM Member Join Date: Dec 2009 Posts: 36 Rep Power: 16	Hi Dia, Maybe, you can give more details about your geometry, like is the inside domain connected with the outside domain? It also would help to make clear, which procedure you are using. Regards, fritz

March 11, 2011, 09:46		#3
nammari New Member Diauddin Nammari Join Date: Mar 2009 Posts: 8 Rep Power: 17	Hi Fritz, Thanks for answering back, that is what I want indeed that the inside domain is connected to the outside domain. Such that I would allow the "wind" to wizz inside the the tank( storage tank) and outside it. If you don't mind what do you mean by procedure ? I am planning to test out a few solvers, and play around with windfoam. As you can get I am trying to avoid "creating" the blockMesh dict by hand, or trying to use other software to create the geometry. Cheers Dia

March 11, 2011, 14:10		#5
nammari New Member Diauddin Nammari Join Date: Mar 2009 Posts: 8 Rep Power: 17	I was trying to create a hollow cylinder with the opening into the domain. So far the cylinders or objects I create are closed. That is my issue. Not how to do that. Cheers Dia

March 11, 2011, 19:49		#6
FG_HSRM Member Join Date: Dec 2009 Posts: 36 Rep Power: 16	Then, I don't understand your problem. It's absolutely the same.