|
[Sponsors] |
Error when post-processing turboPassageRotating2D |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
November 1, 2013, 03:09 |
Error when post-processing turboPassageRotating2D
|
#1 |
New Member
Minh-VietNam
Join Date: Oct 2013
Posts: 7
Rep Power: 12 |
Hi. Everybody.
I'm a new openFoam user. so i can not launch this case. I don't know how to fix the error. Can you help please. This is case (case of an master thesis which downloaded from web http://www.tfd.chalmers.se/~hani/kurser/OS_CFD/) thanks a lot! ====== This is error: --> FOAM FATAL IO ERROR: Cannot find 'value' entry on patch rotor_cyclic_upper of field p in file "/home/minh/Desktop/turboPassageRotating2D/0/p" which is required to set the values of the generic patch field. (Actual type cyclicGgi) Please add the 'value' entry to the write function of the user-defined boundary-condition file: /home/minh/Desktop/turboPassageRotating2D/0/p.boundaryField.rotor_cyclic_upper from line 43 to line 43. From function genericFvPatchField<Type>::genericFvPatchField(con st fvPatch&, const Field<Type>&, const dictionary&) in file genericFvPatchField/genericFvPatchField.C at line 71. FOAM exiting +++ Please show to me, thankS! |
|
November 4, 2013, 04:18 |
|
#2 |
Senior Member
Artur
Join Date: May 2013
Location: Southampton, UK
Posts: 372
Rep Power: 19 |
Can you post the pressure boundary condition file of your case (since that's where the problem is occurring)?
As a side note, I think the title of your post is a bit misleading. All the best, A |
|
November 4, 2013, 05:13 |
turboPassageRotating2d
|
#3 | |
New Member
Minh-VietNam
Join Date: Oct 2013
Posts: 7
Rep Power: 12 |
Quote:
This is my pressure boundary condition. **** dimensions [ 0 2 -2 0 0 0 0 ]; internalField uniform 0; boundaryField { inlet { type zeroGradient; } outlet { type fixedValue; value uniform 0; } fixedWalls { type zeroGradient; } movingwalls { type zeroGradient; } rotor_cyclic_upper { type cyclicGgi; } rotor_cyclic_lower { type cyclicGgi; } stator_cyclics_half0 { type cyclic; } interface1 { type overlapGgi; } interface2 { type overlapGgi; } stator_cyclics_half1 { type cyclic; } } *** Last edited by mingbn; November 4, 2013 at 05:22. Reason: attact file |
||
November 4, 2013, 06:08 |
|
#4 |
Senior Member
Artur
Join Date: May 2013
Location: Southampton, UK
Posts: 372
Rep Power: 19 |
Alright, I think you're using an older version of FOAM since you have "GGI" instead of "AMI", am I right? If yes then I cannot help you since I've only used 2.x and above for sliding meshes. Nonetheless, this is how I define the AMI pressure BC in 2.1.x and 2.2.x and it works:
Code:
AMI1 { type cyclicAMI; value uniform 0; } Good luck, A |
|
November 4, 2013, 22:48 |
|
#5 | |
New Member
Minh-VietNam
Join Date: Oct 2013
Posts: 7
Rep Power: 12 |
Quote:
I am using OpenFoam 2.2.1. I wil try following your advive. |
||
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
post processing for CEL expressions | Niru | CFX | 0 | May 10, 2013 13:13 |
Automated post processing using CFD Post | shreyasr | ANSYS | 0 | January 28, 2013 06:21 |
CFD post processing techniques & streamlining | klk | Main CFD Forum | 0 | October 19, 2010 07:37 |
fluent for post processing | James | FLUENT | 0 | April 21, 2006 04:43 |
post processing in CFD | MANISH BHARGAVA | Main CFD Forum | 0 | October 17, 1998 20:51 |