CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > OpenFOAM

problem due to reconstructPar?

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   June 3, 2011, 16:16
Default problem due to reconstructPar?
  #1
Senior Member
 
Join Date: Nov 2009
Location: Michigan
Posts: 135
Rep Power: 7
doubtsincfd is on a distinguished road
SHM quality check:

Iteration 8
Moving mesh using diplacement scaling : min:0 max:1
Checking faces in error :
non-orthogonality > 65 degrees : 0
faces with face pyramid volume < 1e-20 : 0
faces with concavity > 80 degrees : 0
faces with area < 1e-13 m^2 : 0
faces with skewness > 4 (internal) or 20 (boundary) : 0
faces with interpolation weights (0..1) < 0.06 : 0
faces with volume ratio of neighbour cells < 0.025 : 0
faces with face twist < 0.05 : 0
faces with triangle twist < -0.99 : 0
faces on cells with determinant < 0.001 : 0
Successfully moved mesh
Moved mesh in = 28.71 s
--------------------------------------------------------------------
checkMesh output:
Checking topology...
Boundary definition OK.
Point usage OK.
Upper triangular ordering OK.
Topological cell zip-up check OK.
Face vertices OK.
Number of identical duplicate faces (baffle faces): 43
***Number of faces with non-consecutive shared points: 2396
<<Writing 4878 faces with incorrect edges to set edgeFaces
Number of regions: 1 (OK).

Checking patch topology for multiply connected surfaces ...
Patch Faces Points Surface
block-mesh_FFMaxY 11820 12346 ok (not multiply connected)
block-mesh_FFMinY 10250 10867 ok (not multiply connected)
block-mesh_FFMinX 12100 12716 ok (not multiply connected)
block-mesh_FFMaxX 11258 11927 ok (not multiply connected)
block-mesh_FFMinZ 549 604 ok (not multiply connected)
block-mesh_FFMaxZ 576 625 ok (not multiply connected)
fibs_patch0 1062049 1042114 multiply connected surface (shared edge)
<<Writing 7054 conflicting points to set nonManifoldPoints

Checking geometry...
Domain bounding box: (3.394 2.4 -0.4078) (6.2044 5.2808 1.7)
Boundary openness (7.54504311808e-18 -6.14836063448e-16 -2.51663696261e-17) OK.
Max cell openness = 3.20485835477e-16 OK.
Max aspect ratio = 16.8436403273 OK.
Minumum face area = 1.04855846554e-06. Maximum face area = 0.0562236134114. Face area magnitudes OK.
Min volume = 6.37886579129e-08. Max volume = 0.0131489259567. Total volume = 16.4437716942. Cell volumes OK.
Mesh non-orthogonality Max: 64.9937164346 average: 10.5754013845
Non-orthogonality check OK.
Face pyramids OK.
***Max skewness = 14.5126753746, 1779 highly skew faces detected which may impair the quality of the results
<<Writing 1779 skew faces to set skewFaces
*There are 61015 faces with concave angles between consecutive edges. Max concave angle = 79.996085418 degrees.
<<Writing 61015 faces with concave angles to set concaveFaces
Face flatness (1 = flat, 0 = butterfly) : average = 0.992414013125 min = 0.201691375183
*There are 10729 faces with ratio between projected and actual area < 0.8
Minimum ratio (minimum flatness, maximum warpage) = 0.201691375183
<<Writing 10729 warped faces to set warpedFaces

Failed 2 mesh checks.
-------------------------------------------
Why? Is reconstructParMesh the culprit?
doubtsincfd is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with reconstructPar usergk OpenFOAM 0 December 13, 2010 18:52
Can I solve this problem by Fluent? Kai_kc FLUENT 1 October 27, 2010 05:29
CFX Casting problem: Can it be done all in one? jfasl CFX 1 September 14, 2010 03:14
UDF problem due to using C_U_M1 Rachel FLUENT 0 July 15, 2008 11:13
Incoherent problem table in hollow-fiber spinning Gianni FLUENT 0 April 5, 2008 10:33


All times are GMT -4. The time now is 16:58.