zero-diffusion (constant gradient) boundary condition

thomas99 · July 26, 2011, 08:39

Hi all,

I'm still relatively new to openfoam and despite searching through the tutorials, source code, and this forum have not been able to determine if the zero-diffusion boundary condition is available in openfoam or easily implemented.

Has anyone used this type of boundary condition in openfoam before?

Cheers,
Tom

Cyp · July 26, 2011, 18:01

Hi Tom, and welcome on board!

I believe that the BC you are looking for is zeroGradient. You just have to write " type zeroGradient;" within our patch.

@++
Cyp

thomas99 · July 27, 2011, 04:53

Hi Cyp,

Thanks for the reply! What I'm looking for though is the zero-diffusion outlet boundary condition, not the zero-gradient boundary condition.

A zero-diffusion boundary condition is of the form d^2(phi)/d(n^2) = 0 where phi is a transported variable (e.g. a component of velocity, temperature, viscosity, ...). Typically when this condition is set at an outlet, the value of the node at a particular outlet position is calculated from the interior situated nodes as well as the first derivative which is some constant.

I think both fluent and cfx allow implementation of this boundary condition and wanted to know if openfoam also has this option as I would like to test openfoam for a few studies.

Cheers,
Tom

akidess · July 27, 2011, 07:35

Thomas, have a look at this thread: http://www.cfd-online.com/Forums/ope...condition.html

thomas99 · July 29, 2011, 04:59

Thanks akidess, that's what I was looking for

July 26, 2011, 08:39	zero-diffusion (constant gradient) boundary condition	#1
thomas99 New Member Tom Witten Join Date: May 2011 Location: Freiberg Posts: 10 Rep Power: 14	Hi all, I'm still relatively new to openfoam and despite searching through the tutorials, source code, and this forum have not been able to determine if the zero-diffusion boundary condition is available in openfoam or easily implemented. Has anyone used this type of boundary condition in openfoam before? Cheers, Tom

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
inlet velocity boundary condition	murali	CFX	5	August 3, 2012 08:56
asking for Boundary condition in FLUENT	Destry	FLUENT	0	July 27, 2010 00:55
wall boundary condition with constant velocity	Rogerio Fernandes Brito	CFX	0	August 17, 2008 10:01
Abt 'a constant pressure boundary condition'	jinwon park	Main CFD Forum	3	April 7, 2008 19:36
Calculated gradient boundary condition similar to gammaContactAngle	adona058	OpenFOAM Running, Solving & CFD	0	September 26, 2007 15:23

July 26, 2011, 18:01		#2
Cyp Senior Member Cyprien Join Date: Feb 2010 Location: Stanford University Posts: 299 Rep Power: 18	Hi Tom, and welcome on board! I believe that the BC you are looking for is zeroGradient. You just have to write " type zeroGradient;" within our patch. @++ Cyp

July 27, 2011, 04:53		#3
thomas99 New Member Tom Witten Join Date: May 2011 Location: Freiberg Posts: 10 Rep Power: 14	Hi Cyp, Thanks for the reply! What I'm looking for though is the zero-diffusion outlet boundary condition, not the zero-gradient boundary condition. A zero-diffusion boundary condition is of the form d^2(phi)/d(n^2) = 0 where phi is a transported variable (e.g. a component of velocity, temperature, viscosity, ...). Typically when this condition is set at an outlet, the value of the node at a particular outlet position is calculated from the interior situated nodes as well as the first derivative which is some constant. I think both fluent and cfx allow implementation of this boundary condition and wanted to know if openfoam also has this option as I would like to test openfoam for a few studies. Cheers, Tom

July 27, 2011, 07:35		#4
akidess Senior Member Anton Kidess Join Date: May 2009 Location: Germany Posts: 1,377 Rep Power: 29	Thomas, have a look at this thread: http://www.cfd-online.com/Forums/ope...condition.html

July 29, 2011, 04:59		#5
thomas99 New Member Tom Witten Join Date: May 2011 Location: Freiberg Posts: 10 Rep Power: 14	Thanks akidess, that's what I was looking for