OpenFOAM

Rating Thread / Thread Starter	Last Post	Replies	Views
Sticky: Wiki ( 1 2 3 ... Last Page) gschaider	December 31, 2014 07:34 by wyldckat	178	67,315
Sticky: How to give enough info to get help linnemann	September 20, 2017 09:19 by linnemann	8	55,175
Sticky: How to contribute to the community of OpenFOAM users and to the OpenFOAM technology wyldckat	November 10, 2017 15:54 by rdbisme	17	20,302
Sticky: Map of the OpenFOAM Forum - Understanding where to post your questions! wyldckat	September 2, 2021 05:29 by hakosaj	10	21,557
Sticky: Getting Started with OpenFOAM ( 1 2) wyldckat	August 14, 2022 13:55 by mikethe1wheelnut	25	50,409
Sticky: OpenFOAM.com versus OpenFOAM.org: Which version to use? wyldckat	March 25, 2023 07:50 by ancolli	19	58,913
Obtaining an absurd value for the lift coefficient deeps	August 11, 2010 02:31 by deeps	0	1,238
DNS two-phase flow idrama	August 11, 2010 04:28 by kumar	3	1,855
Solver for U and turbulent variables ayoros	August 11, 2010 07:16 by ayoros	0	1,265
Empty patch problem with Netgen to Openfoam troy	August 11, 2010 08:43 by troy	4	3,600
YPlusRas for InterFoam (Open Foam 1.7) MrD	August 11, 2010 15:44 by MrD	0	4,149
mergePatch question hyperion	August 11, 2010 16:22 by hyperion	0	1,725
what is the best Supersonic outlet boundary condition? universez	August 11, 2010 17:20 by universez	0	2,827
problem in pimpleDyMFoam jayrup	August 12, 2010 00:44 by jayrup	1	1,582
flat plate boundary layer problem --great influence of viscosity waynezw0618	August 12, 2010 02:19 by su_junwei	6	2,135
Divide by zero = printStack ? Rickard.Solsjo	August 12, 2010 03:25 by aut_iut	1	1,728
Help needed with gmshToFoam TomStarke	August 12, 2010 19:12 by TomStarke	1	1,410
Is gravity "g" considered in icoFoam? maysmech	August 12, 2010 21:49 by marupio	3	2,640
Beignner Question: Ejector concept lcnmy	August 12, 2010 22:46 by lcnmy	0	1,930
SimpleFoam convergen problem maolongliu	August 13, 2010 10:17 by maolongliu	7	2,266
Unstable spray for small mesh size (dieselFoam) namCFD	August 13, 2010 15:51 by namCFD	2	2,138
Meshing a pipe joint for OpenFoam--Hex or Tet???? nileshjrane	August 14, 2010 05:38 by nileshjrane	4	4,387
simple question about calculated bc hyperion	August 14, 2010 14:05 by hyperion	0	1,758
Pressure calculation problem maolongliu	August 15, 2010 08:05 by maolongliu	1	1,755
defining boundary condition patches deniggo	August 16, 2010 08:59 by deniggo	0	1,338
Pressure inlet/outlet boundary conditions bruxellois4	August 16, 2010 19:44 by bruxellois4	0	1,869
Modeling vortex creation past vertical flat wall LES model shackman287	August 17, 2010 18:51 by shackman287	0	1,907
A question related to defining a variable daveatstyacht	August 17, 2010 20:53 by daveatstyacht	3	1,653
comparison openfoam - cfx alfa_8C	August 18, 2010 05:07 by alfa_8C	0	1,604
Modelling a Herschel Bulkley fluid with yield stress proportional to fluid pressure carrotlaw	August 18, 2010 06:57 by carrotlaw	0	2,722
slip ratio between gas/liquid Robat	August 18, 2010 09:05 by holger_marschall	3	3,039
Hentalpy equation openfoam - miss a term lions85	August 18, 2010 12:12 by chandramurthy	2	3,297
Please confirm, if this is a bug or a typo N. A.	August 18, 2010 12:51 by N. A.	0	1,392
two Phase column simulation chemeng	August 18, 2010 12:53 by soccol	3	3,504
Mesh Updating gimli79	August 18, 2010 17:31 by vonboett	11	2,422
Failed to load data file: cavity.OpenFOAM c120613	August 19, 2010 07:01 by wyldckat	3	3,361
bubbleFoam validation case balkrishna	August 19, 2010 07:05 by balkrishna	0	1,462
TwoPhaseEulerfoam - question soccol	August 19, 2010 08:10 by soccol	3	1,502
dsmc properties hyperion	August 19, 2010 09:58 by archymedes	1	2,701
turbulentTemperatureCoupledBaffle in chtMultiRegion stawrogin	August 19, 2010 14:22 by stawrogin	0	2,275
adapt offset cylinder model for les turbulence shackman287	August 19, 2010 21:10 by shackman287	0	2,226
NSRDS functions, liquid properties mystix	August 20, 2010 05:10 by mystix	2	2,699
ParaView Rickard.Solsjo	August 20, 2010 06:31 by fabianpk	1	1,347
ParaView shows a list of data types and ask for it idrama	August 20, 2010 07:08 by val46	1	1,340
calcMassFlow - problem in v1.6 betakv	August 20, 2010 07:13 by raagh77	4	2,318
fluid to solid heattransfer with chtMultiRegionFoam schteff	August 20, 2010 07:45 by schteff	5	1,914

Read this first: How to ask a question on the forums

Page 42 of 239

« First

142

Last »

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

All times are GMT -4. The time now is 12:03.