Phi to Phida
 

Is it possible to covert PHI into PHIDA? Could anyone tell me how to do that? Thanks.

Re: Phi to Phida
 

I never tried this before. But I assume you can first load the case in VR editor, change the setting in VR for phi to phida and then save the case file. Give it a try!

Re: Phi to Phida
 

Try to load your case in VR Editor, change output to PHI, and restart for 2-3 iterations. And you will have phi file!

Re: Phi to Phida
 

The method suggested in the first reply certainly won't work, as VR-Editor only copies existing PHI/PHIDA files to the saved names. The second won't either, as Earth isn't quite clever enough to read a PHI file and write a PHIDA. It expects input and output to be in the same format.

You can switch format from PHI->PHIDA or PHIDA->PHI using the little-known PINTO program. This is run from a DOS command prompt by the command runpin. It needs an input file Q1PIN. To convert from PHI->PHIDA the Q1PIN file should contain:

LDA=T STOP

After running, a new file called NPHIDA will have been created.

To go from PHIDA->PHI it should contain:

LFS=T STOP

After running a new file NPHI will have been created. These new files can be renamed as required.

More information on PINTO can be found in the POLIS Ecyclopaedia under P. http://www.cham.co.uk/phoenics/d_polis/d_info/pinto.htm

Re: Phi to Phida
 

Thanks. However, it was able to convert a phida file to NPHI but it cannot convert a phi file into NPHIDA. I don't know where is the problem because I did replace LFS=T by LDA=T in Q1pin. I'm using PHOENICS 3.4.

More help is needed!

Ther error message is as follows.

---------------------------------------------------------

CCCC HHH PHOENICS Version 3.3.1 - PINTO

CCCCCCCC HHHHH (C) Copyright 2000

CCCCCCC HHHHHHHHHH Concentration Heat and Momentum Ltd

CCCCCCC HHHHHHHHHHHH All rights reserved.

CCCCCC HHHHHHHHHHHHH Address: Bakery House, 40 High St

CCCCCCC HHHHHHHHHHHH Wimbledon, London, SW19 5AU

CCCCCCC HHHHHHHHHH Tel: 0208-947-7651

CCCCCCCC HHHHH Facsimile: 0208-879-3497

CCCC HHH E-mail: phoenics@cham.demon.co.uk

--------------------------------------------------------- This program forms part of the PHOENICS installation for:

CHAM

---------------------------------------------------------

PINTO PROGRAM DATED 31.12.00 ERROR IN OPENING FILE: PHIDA ( LU: 39 ;IOPEN: 7 ;LREC: 1024 ;IOSTAT: 602 )

ERROR STOP REACHED CHECK DATA. < was unexpected at this time.

Re: Phi to Phida
 

The IOSTAT:602 part of the error report has the following definition in the Compaq Fortran help-

severe (602): File not found FOR$IOS_F6416. An OPEN statement specified STATUS='OLD' for a specified file or a directory path that does not exist.

Is it possible that you do not have a file called phida in the directory from which you are running?

Could be your file format setting is wrong.

To convert PHI -> PHIDA you must have: # PHIDA=F in PREFIX (formatted in Options - File format) to make PINTO pick up a PHI file # LDA=T in Q1PIN to make it write an NPHIDA # a file called PHI in the working directory

To convert PHIDA -. PHI you must have # PHIDA=T in PREFIX (direct access in Options - File format) to make it pick up a PHIDA file # LFS=T in Q1PIN to make it write an NPHI # a file called PHIDA in the working directory

If this still doesn't work, send your Q1PIN, PREFIX and PHI (zipped!) to support@cham.co.uk. They will try to see what is wrong.

Re: Phi to Phida
 

It works! The problem was in the PREFIX. It need be changed to PHIDA=F if I want to convert PHI into PHIDA by PINTO.

Thanks a lot!