How can I run a private GENTRA

December 21, 2003, 01:22

The version is 3.5. I want to change the output format of GHIS because the partical number is over 10000. But the partical number formant is "I4". Therefor I change the code in GENTRA: C * ------------------- SECTION 8 ---- FINISH OF TIME STEP.

ELSEIF(ISC.EQ.8) THEN

IF(GHFILE(1:4).NE.'NONE') THEN

IF(.NOT.STEADY.AND.(NX.EQ.1.OR.NY.EQ.1.OR.NZ.EQ.1) ) THEN

DO I= 1, NTRACK

ILOC0= IPFSTR(I)+IPRSTN

IWRT= ISTEP

IF(I.EQ.1) IWRT= -ISTEP

WRITE(LUHIS,'(I6,A,11(1PE13.3))')IWRT,' ',

+ TIM, (F(ILOC0+J),J=1, 10),

ENDDO

ENDIF

ENDIF

Then I compile and link the gentra and earth and set the earth version as private. But the output format in GHIS has no change. Then I open the BLDEAR.BAT and find that gentra.for has been compiled and linked. The private earth.exe is runed. But why the format is not changed? Thanks.

December 25, 2003, 06:12

If you run a steady or 3D case,what you modified is no meaning here.

December 27, 2003, 01:10

Then how can I change the output format of GHIS? My case is steady and 3d. Thanks

January 6, 2004, 06:48

I think you can not modify the format of GHIS. The format is not open to users.

December 21, 2003, 01:22	How can I run a private GENTRA	#1
ben Guest Posts: n/a	The version is 3.5. I want to change the output format of GHIS because the partical number is over 10000. But the partical number formant is "I4". Therefor I change the code in GENTRA: C * ------------------- SECTION 8 ---- FINISH OF TIME STEP. ELSEIF(ISC.EQ.8) THEN IF(GHFILE(1:4).NE.'NONE') THEN IF(.NOT.STEADY.AND.(NX.EQ.1.OR.NY.EQ.1.OR.NZ.EQ.1) ) THEN DO I= 1, NTRACK ILOC0= IPFSTR(I)+IPRSTN IWRT= ISTEP IF(I.EQ.1) IWRT= -ISTEP WRITE(LUHIS,'(I6,A,11(1PE13.3))')IWRT,' ', + TIM, (F(ILOC0+J),J=1, 10), ENDDO ENDIF ENDIF Then I compile and link the gentra and earth and set the earth version as private. But the output format in GHIS has no change. Then I open the BLDEAR.BAT and find that gentra.for has been compiled and linked. The private earth.exe is runed. But why the format is not changed? Thanks.

December 25, 2003, 06:12	Re: How can I run a private GENTRA	#2
xz Guest Posts: n/a	If you run a steady or 3D case,what you modified is no meaning here.

December 27, 2003, 01:10	Re: How can I run a private GENTRA	#3
ben Guest Posts: n/a	Then how can I change the output format of GHIS? My case is steady and 3d. Thanks

January 6, 2004, 06:48	Re: How can I run a private GENTRA	#4
xz Guest Posts: n/a	I think you can not modify the format of GHIS. The format is not open to users.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Access private data member	lr103476	OpenFOAM Running, Solving & CFD	3	May 5, 2018 21:44
ABOUT GENTRA	WING	Phoenics	1	August 30, 2006 03:49
private tuition for a cfd assignment - payment	ahmed	Main CFD Forum	4	August 10, 2005 09:15
Site devoted to private experience of application	Dr. A.Ivanov	Phoenics	6	November 28, 2002 04:05
Private Ground	Mohamed Ouzzane	Phoenics	4	June 10, 2002 11:11