Forum: OpenFOAM
April 6, 2014, 02:19
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
March 22, 2014, 12:29
|
Replies: 59
Views: 9,801
Hi Lucas,
When I first create my regions, I...
Hi Lucas,
When I first create my regions, I got the same kind of problem. Like making excess domains. It is not due to type of the topoSet dictionary. You can view the excess domain by using...
|
Forum: OpenFOAM
March 22, 2014, 03:16
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
March 7, 2014, 12:32
|
Replies: 59
Views: 9,801
changing the boundary conditions with time
Dear Bruno,
I want to run the chtMultiRegionFoam with different inlet temperature and velocity magnitudes at different times. For example, lets say I want to change the inlet temperature of the...
|
Forum: OpenFOAM
March 3, 2014, 00:49
|
Replies: 59
Views: 9,801
Dear Bruno,
Thank you very much. When I set...
Dear Bruno,
Thank you very much. When I set the time step to 0.01 and remove the grading in the Z-direction by catching the U-part of the pipe with another block with dz=0.012, the error didn't...
|
Forum: OpenFOAM
February 26, 2014, 11:39
|
Replies: 59
Views: 9,801
error occured in chtMultiRegionFoam
Dear Bruno,
here is part of the full error message:
Solving for fluid region water
diagonal: Solving for rho, Initial residual = 0, Final residual = 0, No Iterations 0
DILUPBiCG: Solving...
|
Forum: OpenFOAM
February 26, 2014, 11:29
|
Replies: 59
Views: 9,801
error occured in chtMultiRegionFoam
Dear Bruno,
I have created a case which have four different materials (water,pipe,filling material, soil). I use blockMesh to create the domain and then use the topoSet to define the regions. This...
|
Forum: OpenFOAM
February 3, 2014, 17:11
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
February 2, 2014, 23:59
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 27, 2014, 11:30
|
Replies: 59
Views: 9,801
Dear Bruno,
These are the steps I...
Dear Bruno,
These are the steps I followed,if in case you need to check them,
P { margin-bottom: 0.08in; } runApplication blockMesh
#define the cell set "refineCells" for...
|
Forum: OpenFOAM
January 27, 2014, 11:11
|
Replies: 59
Views: 9,801
Dear Bruno,
I am back again after long time...
Dear Bruno,
I am back again after long time finishing all the exams.
I have followed the steps you mentioned in the above. I still have maxZ face at the inlet and outlet faces. I use the...
|
Forum: OpenFOAM
January 14, 2014, 16:28
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 6, 2014, 15:15
|
Replies: 59
Views: 9,801
Dear Bruno,
Thank you very much. I actually...
Dear Bruno,
Thank you very much. I actually run,
topoSet -dict system/topoSetDict01
I didn't use the Allrun command. That is why I forgot to put the correct name for the topoSet in the...
|
Forum: OpenFOAM
January 5, 2014, 17:05
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 5, 2014, 15:33
|
Replies: 59
Views: 9,801
Dear Bruno,
Thanks. Yes, as you said, I...
Dear Bruno,
Thanks. Yes, as you said, I looked in to the "0/water/polyMesh/boundary". There are faces associated to the maxZ. So, it means, if I included the topoSet for faceSet defining inlet...
|
Forum: OpenFOAM
January 5, 2014, 13:58
|
Replies: 59
Views: 9,801
Dear Bruno,
I am sorry for disturbing you. I...
Dear Bruno,
I am sorry for disturbing you. I actually did the other way around for the previous case, without go into refining the mesh
1.blockMesh
2.topoSet defining faceSet for inlet and...
|
Forum: OpenFOAM
January 5, 2014, 12:52
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 5, 2014, 12:32
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 5, 2014, 11:02
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 5, 2014, 09:40
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
January 5, 2014, 04:57
|
Replies: 59
Views: 9,801
Grading the mesh for chtMultiRegionFoam
Dear Bruno,
The instructions you gave worked perfectly. Now I have another problem, As I didn't give any cell expansion ratio, the number of cells are so high. Therefore, I cannot load the soil...
|
Forum: OpenFOAM
December 28, 2013, 13:43
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
December 28, 2013, 09:18
|
Replies: 59
Views: 9,801
|
Forum: OpenFOAM
December 28, 2013, 07:47
|
Replies: 59
Views: 9,801
Many thanks again. Do you mean that...
Many thanks again. Do you mean that "createPatchDict" is better than "faceSet"?. So, what should I really have a look at between these two? Do you think "createPatchDict" will give better solutions...
|
Forum: OpenFOAM
December 27, 2013, 15:07
|
Replies: 59
Views: 9,801
|