Search Results

User Name Remember Me Password

Showing results 1 to 7 of 7 Search took 0.00 seconds. Search: Posts Made By: diamondx

Forum: ANSYS Meshing & Geometry October 17, 2012, 21:11

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx yes that's was i was reffering to, may be more if... yes that's was i was reffering to, may be more if you can handle large large element. keep your original outlet. declare them as internal wall, and export them as interior...

Forum: ANSYS Meshing & Geometry October 16, 2012, 13:56

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx it worked for one geometry but not the other.... it worked for one geometry but not the other. trying to investigate the problem more... i realized that the one in which it didn't work had a bad geometry... I'll try everything once again this week...

Forum: ANSYS Meshing & Geometry October 16, 2012, 13:35

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx could you get a good blocking so far ?? could you get a good blocking so far ??

Forum: ANSYS Meshing & Geometry October 16, 2012, 13:28

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx @far i will , i'm a little bit busy right now...... @far i will , i'm a little bit busy right now... we keep in touch

Forum: ANSYS Meshing & Geometry October 16, 2012, 13:10

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx keep the inlet and outlet in your geometry, in... keep the inlet and outlet in your geometry, in the meshing tab, declare them as "internal wall". Now, extend your outlet. In fluent, the extended outlet will be the real outlet, and the outlet that...

Forum: ANSYS Meshing & Geometry October 12, 2012, 18:47

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx i think it's more because of your geometry than... i think it's more because of your geometry than your mesh. You outlet is way too close to your inlet... what are you trying to model ??

Forum: ANSYS Meshing & Geometry October 12, 2012, 15:12

Replies: 36 [ICEM] geometry repair Views: 4,739 Posted By diamondx 0.4 is ok for fluent !! give it a try... 0.4 is ok for fluent !! give it a try...

Showing results 1 to 7 of 7

Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home General Forums     Main CFD Forum     System Analysis     Structural Mechanics     Electromagnetics     CFD Freelancers     Hardware     Lounge Software User Forums     ANSYS         CFX         FLUENT             Fluent Multiphase             Fluent UDF and Scheme Programming         ANSYS Meshing & Geometry     Autodesk Simulation CFD     AVL FIRE     COMSOL     CONVERGE     Fidelity CFD     FloEFD, FloWorks & FloTHERM     FLOW-3D     OpenFOAM         OpenFOAM News & Announcements             OpenFOAM Announcements from ESI-OpenCFD             OpenFOAM Announcements from OpenFOAM Foundation             OpenFOAM Announcements from Other Sources         OpenFOAM Installation         OpenFOAM Meshing & Mesh Conversion         OpenFOAM Pre-Processing         OpenFOAM Running, Solving & CFD         OpenFOAM Post-Processing         OpenFOAM Programming & Development         OpenFOAM Verification & Validation         OpenFOAM Community Contributions             OpenFOAM CC Toolkits for Fluid-Structure Interaction         OpenFOAM Journal         OpenFOAM Bugs     Phoenics     REEF3D         REEF3D News & Announcements     Siemens         STAR-CCM+         STAR-CD     SU2         SU2 News & Announcements         SU2 Installation         SU2 Shape Design Mesh Generation & Pre-Processing Software     ANSA     enGrid     GridPro     Pointwise & Gridgen Visualization & Post-Processing Software     EnSight     FieldView     ParaView     Tecplot Special Topics     Mesh Generation & Pre-Processing     Visualization & Post-Processing CFD Online Community     Site News & Announcements     Site Help, Feedback & Discussions     CFD-Wiki