Maneuvering Simulation with 6-DOF Body

TSC · October 29, 2013, 04:55

Hello everyone,

I got a serious question about maneuvering simulation in star-ccm+:

so far i try to simulate a 10/10 Z-Maneuver for a model scale container vessel. The vessel should be able to move in x and y-direction, but also rotate about the z-axis. The question for now is: do I need overset grid to simulate the translation and rotation, or is there any othe possibility to save some cells?

Regards
Tim

ryancoe · October 29, 2013, 09:27

Tim,

You can accomplish this without any sort of dynamic mesh method (e.g., overset grids) unless you want a moving rudder and/or propeller. In fact, I used STAR-CCM+ to do maneuvering analysis of AUVs during my PhD research (http://vtechworks.lib.vt.edu/handle/10919/23777).

TSC · October 30, 2013, 03:54

Hello Ryan,

first, congratulation for your PhD Thesis.

As you have already accepted, I want to simulate a moving rudder and a rotating propeller for maneuvering test. Therefore an overset grid is the best way to accomplish the rotating parts, in my opinion.
For now I am in the very first beginning of the porject and want to check all the possibilitys (thanks for the link). Maybe there are some further wuestions after reading your thesis

Regards
Tim

October 29, 2013, 04:55	Maneuvering Simulation with 6-DOF Body	#1
TSC New Member Tim Join Date: Dec 2012 Posts: 7 Rep Power: 13	Hello everyone, I got a serious question about maneuvering simulation in star-ccm+: so far i try to simulate a 10/10 Z-Maneuver for a model scale container vessel. The vessel should be able to move in x and y-direction, but also rotate about the z-axis. The question for now is: do I need overset grid to simulate the translation and rotation, or is there any othe possibility to save some cells? Regards Tim

October 29, 2013, 09:27		#2
ryancoe Member Ryan Coe Join Date: Jun 2010 Location: Albuquerque, NM Posts: 98 Rep Power: 15	Tim, You can accomplish this without any sort of dynamic mesh method (e.g., overset grids) unless you want a moving rudder and/or propeller. In fact, I used STAR-CCM+ to do maneuvering analysis of AUVs during my PhD research (http://vtechworks.lib.vt.edu/handle/10919/23777). __________________ Ryan

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Ahmed body simulation	alenglaro	FLUENT	21	March 9, 2016 05:19
[Need some advise] Am I doing right?? Simulating a rotational mixer	setasena	STAR-CCM+	4	March 10, 2013 10:32
How to calculate body forcefor 2d wedge impact simulation	khurrammtc	FLUENT	0	August 14, 2012 02:11
Fan simulation divergence	ayothicfd	CFX	18	July 20, 2012 05:53
Submarged body simulation in Fluent 6.3.26	Behnam	FLUENT	0	April 22, 2009 06:10

October 30, 2013, 03:54		#3
TSC New Member Tim Join Date: Dec 2012 Posts: 7 Rep Power: 13	Hello Ryan, first, congratulation for your PhD Thesis. As you have already accepted, I want to simulate a moving rudder and a rotating propeller for maneuvering test. Therefore an overset grid is the best way to accomplish the rotating parts, in my opinion. For now I am in the very first beginning of the porject and want to check all the possibilitys (thanks for the link). Maybe there are some further wuestions after reading your thesis Regards Tim