Mass & Heat Transfer

sheintz · April 16, 2010, 05:08

Hi everybody ^^

I'm using StarCD 3.26 for the simulation of a spray.

I would like to use the mass transfer subroutine (and the heat transfer subroutine) but when I launch the calculation I have one error :

***ERROR *** Compilation error in user file "ufile/conduc.f"

Before I do with this mass (heat) transfer subroutine I din#t have this error, what do I have to do in the conduc-file ?

Thank you in advance
Best regards

Simon

sheintz · April 28, 2010, 03:31

I have found the solution :
I had to remove the subroutine files (conduc.f , specht.f , viscos.f , ...).
So easy !
I hope it can help someone else.

shin26 · May 14, 2011, 08:20

Hello simon
well i'm Samy and i'm trying to finish my simulation using STARCD 4 well i'm done with the geometry i built it with Star design and i added boundaries condition and i did the running even in the pro star but the problem is:
btw i'm simulating flow in a concentric tube (heat exchanger) you know and interior tuve and another anulus, well the probleme is i dont have a temperature variation in the two channels , so i think i have to use subroutines and i dont master the porous media stuffs, because i have to add on the annulus channel a porous media like chicanes and so, so if you can help me with that it will be great and if you can exchange mails to discuss on it , it will be very nice

thank you
Samy

April 16, 2010, 05:08	Mass & Heat Transfer	#1
sheintz Member Heintz Simon Join Date: Sep 2009 Location: Germany Posts: 36 Rep Power: 16	Hi everybody ^^ I'm using StarCD 3.26 for the simulation of a spray. I would like to use the mass transfer subroutine (and the heat transfer subroutine) but when I launch the calculation I have one error : *ERROR * Compilation error in user file "ufile/conduc.f" Before I do with this mass (heat) transfer subroutine I din#t have this error, what do I have to do in the conduc-file ? Thank you in advance Best regards Simon

May 14, 2011, 08:20	hello	#3
shin26 New Member Join Date: May 2011 Posts: 3 Rep Power: 14	Hello simon well i'm Samy and i'm trying to finish my simulation using STARCD 4 well i'm done with the geometry i built it with Star design and i added boundaries condition and i did the running even in the pro star but the problem is: btw i'm simulating flow in a concentric tube (heat exchanger) you know and interior tuve and another anulus, well the probleme is i dont have a temperature variation in the two channels , so i think i have to use subroutines and i dont master the porous media stuffs, because i have to add on the annulus channel a porous media like chicanes and so, so if you can help me with that it will be great and if you can exchange mails to discuss on it , it will be very nice thank you Samy

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
mass flow in is not equal to mass flow out	saii	CFX	12	March 19, 2018 05:21
About phase change heat and mass transfer	Michael	FLUENT	2	February 13, 2011 01:49
Convective / Conductive Heat Transfer in Hypersonic flows	enigma	Main CFD Forum	2	November 1, 2009 22:53
Natural convection - Inlet boundary condition	max91	CFX	1	July 29, 2008 20:28
Convective Heat Transfer - Heat Exchanger	Mark	CFX	6	November 15, 2004 15:55

April 28, 2010, 03:31		#2
sheintz Member Heintz Simon Join Date: Sep 2009 Location: Germany Posts: 36 Rep Power: 16	I have found the solution : I had to remove the subroutine files (conduc.f , specht.f , viscos.f , ...). So easy ! I hope it can help someone else.