# Discrete Operator Splitting

### From CFD-Wiki

Kennkqzhang (Talk | contribs) (→External link) |
m |
||

Line 1: | Line 1: | ||

- | Different from many other pressure-velocity decoupling method, in Discrete Operator Splitting (DOS) method, the fully coupled discrete system is first obtained (with all boundary conditions taken into account). Next, the coupled system is split, sufficiently and necessarily, into two smaller (more importantly, well-natured) subsytems, which are coupled through source terms. Then, these two subsystems are iterated within each time marching step. DOS requires no numerical boundary conditions. The method is described as follows | + | Different from many other pressure-velocity decoupling method, in Discrete Operator Splitting (DOS) method, the fully coupled discrete system is first obtained (with all boundary conditions taken into account). Next, the coupled system is split, sufficiently and necessarily, into two smaller (more importantly, well-natured) subsytems, which are coupled through source terms. Then, these two subsystems are iterated within each time marching step. DOS requires no numerical boundary conditions. The method is described as follows: |

Discretization of the momentum and continuity equation eventually leads to the following system | Discretization of the momentum and continuity equation eventually leads to the following system | ||

Line 88: | Line 88: | ||

definite subsystems. The reverse MUST be proved, so that they are equivalent to each other. The reverse can be found in the external link of this article. | definite subsystems. The reverse MUST be proved, so that they are equivalent to each other. The reverse can be found in the external link of this article. | ||

- | In CCPPE (Consistent Continuous Pressure Poisson Equation), the continuous pressure poisson equation is first derived and assigned with numerical boundary condtions (not physical boundary conditions), and the resulting system is involved with linear iteration only (suppose the nonlinear term is already linearized in time). In contrast, the DOS involves source-term iteration and linear iteration. However, while in actual practice a strict convergence criterion is imposed on the source-term iteration, only few prescibed number of iterations are imposed on the linear iteration inside the source-term iteration. | + | In CCPPE (Consistent Continuous Pressure Poisson Equation), the continuous pressure poisson equation is first derived and assigned with numerical boundary condtions (not physical boundary conditions), and the resulting system is involved with linear iteration only (suppose the nonlinear term is already linearized in time). In contrast, the DOS involves source-term iteration and linear iteration. However, while in actual practice a strict convergence criterion is imposed on the source-term iteration, only few prescibed number of iterations are imposed on the linear iteration inside the source-term iteration. Actual practice shows that when the solution reaches the level that the source-term iteration is nearly complete, the same solution also reaches the level that the criterion for the linear iteration is easily met. Hence, apart from offering simplicity and no requirement of numerical boundary conditions, DOS is efficient. |

## Latest revision as of 16:25, 28 December 2010

Different from many other pressure-velocity decoupling method, in Discrete Operator Splitting (DOS) method, the fully coupled discrete system is first obtained (with all boundary conditions taken into account). Next, the coupled system is split, sufficiently and necessarily, into two smaller (more importantly, well-natured) subsytems, which are coupled through source terms. Then, these two subsystems are iterated within each time marching step. DOS requires no numerical boundary conditions. The method is described as follows:

Discretization of the momentum and continuity equation eventually leads to the following system

where in the momentum equation is the coefficient matrix for the velocity, is the coefficient matrix for the pressure, in the continuity equation is the coefficient matrix for the velocity, and and are the right-hand-side known vectors for the momentum and the continuity equations, respectively. It is well known that such a system is ill-conditioned, which causes difficulty to directly or iteratively solve the whole large system simultaneously. We split matrix into the diagonal part () and the off-diagonal part

where stands for the inverse of . Let the continuity equation be incorporated into the above momentum equation and let the original momentum equation retained, we obtain the following system

For convenience, we define

so that the discrete forms of the momentum equation and the continuity equation become

Furthermore, let's define

finally we have two well-posed subsystems

So far it has been proved that the original indefinite system implies the two definite subsystems. The reverse MUST be proved, so that they are equivalent to each other. The reverse can be found in the external link of this article.

In CCPPE (Consistent Continuous Pressure Poisson Equation), the continuous pressure poisson equation is first derived and assigned with numerical boundary condtions (not physical boundary conditions), and the resulting system is involved with linear iteration only (suppose the nonlinear term is already linearized in time). In contrast, the DOS involves source-term iteration and linear iteration. However, while in actual practice a strict convergence criterion is imposed on the source-term iteration, only few prescibed number of iterations are imposed on the linear iteration inside the source-term iteration. Actual practice shows that when the solution reaches the level that the source-term iteration is nearly complete, the same solution also reaches the level that the criterion for the linear iteration is easily met. Hence, apart from offering simplicity and no requirement of numerical boundary conditions, DOS is efficient.