|
[Sponsors] |
[ICEM] volume mesh leaking out of the surface, in a multi zone problem |
![]() |
|
LinkBack | Thread Tools | Search this Thread | Display Modes |
![]() |
![]() |
#1 |
New Member
Prem Chand
Join Date: Dec 2011
Posts: 3
Rep Power: 13 ![]() |
Hi everyone
I am starting a thread for the first time and i am an ameteur when it comes to ICEM CFD. The problem that i have at hand is, conjugate analysis of turbine blade, and have to mesh different zones in the domain. I have started with blocking but it seems like a hectic task to block all the protrusions and holes in the geometry, so moved to tetra meshing. Initially i had problem with holes in the geometry but now i think i have cleared them (as all i could see are only red lines after build topology). when iam meshing a particular zone, the surface mesh is ok but the volume mesh in that zone is leaking out and not in one point but completely around the surface. can somebody help me solve the problem? |
|
![]() |
![]() |
![]() |
![]() |
#2 |
New Member
abdul
Join Date: Mar 2012
Posts: 9
Rep Power: 13 ![]() |
i am also having the same problem
but my domain is temperature reduction valve the problem is "There is a leak in the mesh" There is a leak in the mesh material ORFN/-1 can reach material fluid.1 thanks in ADVANCE |
|
![]() |
![]() |
![]() |
![]() |
#3 |
Senior Member
|
did you guys create the "body" ??!!!
|
|
![]() |
![]() |
![]() |
![]() |
#4 |
New Member
Prem Chand
Join Date: Dec 2011
Posts: 3
Rep Power: 13 ![]() |
Hi
I have changed the format in which am importing the geometry. Previously i have used the IGES format. After strenuous efforts with the geometry repair, i have tried importing in Parasolid format and it worked. Now I dont have any leakage in the mesh. Try importing in Parasolid format. regards Prem Chand |
|
![]() |
![]() |
![]() |
![]() |
#5 |
Senior Member
|
but IGES format should not cause any problem because i have been working on it...
|
|
![]() |
![]() |
![]() |
![]() |
#6 |
New Member
abdul
Join Date: Mar 2012
Posts: 9
Rep Power: 13 ![]() |
thanx guys for all ur reply
but the thing is i am importing in Parasolid format only, i am getting some surface got away and i got empty surface what should i do thankx in advance |
|
![]() |
![]() |
![]() |
![]() |
#7 |
New Member
abdul
Join Date: Mar 2012
Posts: 9
Rep Power: 13 ![]() |
||
![]() |
![]() |
![]() |
Tags |
mesh leakage, zones |
Thread Tools | Search this Thread |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
[ICEM] Negative volume error in hybrid mesh | siw | ANSYS Meshing & Geometry | 4 | September 3, 2014 05:25 |
[blockMesh] Problem with Mesh Volume | seboxx | OpenFOAM Meshing & Mesh Conversion | 3 | January 30, 2012 08:19 |
Problem in IMPORT of ICEM input file in FLUENT | csvirume | FLUENT | 2 | September 9, 2009 01:08 |
[blockMesh] Axisymmetrical mesh | Rasmus Gjesing (Gjesing) | OpenFOAM Meshing & Mesh Conversion | 10 | April 2, 2007 14:00 |
Sliding mesh error | Karl Kevala | FLUENT | 4 | February 21, 2001 15:52 |