[ANSYS Meshing] Problem converting mesh to parasolid in FE Modeler

mcknoche · November 11, 2015, 09:14

I am trying to do MEMS multiphysics simulation which involves pressure to an object to determine deformation, and then evaluating the capacitance of the deformed object.

Currently I can complete the deformation in Ansys Mechanical with no problem and the meshing includes contact meshing algorithms and uses MPC formulation so that no penetration of objects should occur.

I then export the mesh as a cdb file, and try to convert to parasolid for further EM simulations using FE Modeler. In FE modeler, I am getting the error:

"The Parasolid conversion failed for this geometry. Try to change the Skin Detection Tool parameters to obtain a more refined geometry."

I have tried many different meshing algorithms as well as different skin detection tools settings to no avail. The only thing odd to me is that in FE Modeler, under Mesh diagnostics, I get two warnings ("Beams do not have cross-section properties" and "Semi-parabolic elements"). I do not know how to eliminate these warnings because I do not specify a beam anywhere in ANSYS Mechanical.

Any help would be greatly appreciated since I am new to ANSYS.

maa_generals · July 6, 2016, 10:35

Hi,
I have a very similar problem!
i need to evaluate the inside volume of deformed shape . i tried your procedure too but my parasolid file was not appropriate for further simulations because it had lots of gaps and uncoordinated surfaces...
also i have surfaces in parasolid file and how can i use them as solids??!!!!

did you find any solutions???
thanks a lot...

November 11, 2015, 09:14	Problem converting mesh to parasolid in FE Modeler	#1
mcknoche New Member Michael Join Date: Nov 2015 Posts: 1 Rep Power: 0	I am trying to do MEMS multiphysics simulation which involves pressure to an object to determine deformation, and then evaluating the capacitance of the deformed object. Currently I can complete the deformation in Ansys Mechanical with no problem and the meshing includes contact meshing algorithms and uses MPC formulation so that no penetration of objects should occur. I then export the mesh as a cdb file, and try to convert to parasolid for further EM simulations using FE Modeler. In FE modeler, I am getting the error: "The Parasolid conversion failed for this geometry. Try to change the Skin Detection Tool parameters to obtain a more refined geometry." I have tried many different meshing algorithms as well as different skin detection tools settings to no avail. The only thing odd to me is that in FE Modeler, under Mesh diagnostics, I get two warnings ("Beams do not have cross-section properties" and "Semi-parabolic elements"). I do not know how to eliminate these warnings because I do not specify a beam anywhere in ANSYS Mechanical. Any help would be greatly appreciated since I am new to ANSYS.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
decomposePar problem: Cell 0contains face labels out of range	vaina74	OpenFOAM Pre-Processing	37	July 20, 2020 05:38
Gambit problems	Althea	FLUENT	22	January 4, 2017 03:19
[Commercial meshers] Problem converting fluent mesh	vinz	OpenFOAM Meshing & Mesh Conversion	28	October 12, 2015 06:37
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55
unstructured vs. structured grids	Frank Muldoon	Main CFD Forum	1	January 5, 1999 10:09

July 6, 2016, 10:35		#2
maa_generals New Member majid Join Date: Jan 2016 Posts: 4 Rep Power: 10	Hi, I have a very similar problem! i need to evaluate the inside volume of deformed shape . i tried your procedure too but my parasolid file was not appropriate for further simulations because it had lots of gaps and uncoordinated surfaces... also i have surfaces in parasolid file and how can i use them as solids??!!!! did you find any solutions??? thanks a lot...