[DesignModeler] Modelling of Heat transfer

Turtle · August 30, 2012, 04:42

Hey everyone,

I need some help in modelling a system, where water flows through a Cu-pipe and heat is transfered through the walls of the pipe into a surrounding material.

Which modell shall i take for this? Thermal-transient? And how can I make the geometry so that Ansys knows what's which material? Also, I dont know how to combine a mass flow (water) with the heat transfer.

Help much appreciated...

Greetings
Turtle

diamondx · August 30, 2012, 09:34

please adress you problem in the fluent section. when you have walls, you can set their thickness and their materials in ansys...

zaynah04 · September 8, 2012, 05:58

Dear Ali
I have a problem in gambit i define porous_jump, then in fluent it sent an error message:
Error: Cannot change po to porous-jump because
there is only one adjacent cell thread.

i have tried modify in gambit and its still futile.
can you please guide me?

Thanks
zaynah

diamondx · September 8, 2012, 12:59

I don't have gambit installed... i never used. i wish i can help.

zaynah04 · September 8, 2012, 14:44

Dear Ali

Its okay...

Zaynah

abdul Sami · September 9, 2012, 07:30

Hi every One!

i want to know that in ansys how i create thick mesh near the boundries(in 2d nozzle) and in the centre it should be thin plz help any one plzz

August 30, 2012, 04:42	Modelling of Heat transfer	#1
Turtle New Member Join Date: Aug 2012 Location: Germany Posts: 5 Rep Power: 13	Hey everyone, I need some help in modelling a system, where water flows through a Cu-pipe and heat is transfered through the walls of the pipe into a surrounding material. Which modell shall i take for this? Thermal-transient? And how can I make the geometry so that Ansys knows what's which material? Also, I dont know how to combine a mass flow (water) with the heat transfer. Help much appreciated... Greetings Turtle Last edited by Turtle; September 8, 2012 at 09:25.

August 30, 2012, 09:34		#2
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	please adress you problem in the fluent section. when you have walls, you can set their thickness and their materials in ansys... __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

September 8, 2012, 12:59		#4
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	I don't have gambit installed... i never used. i wish i can help. __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

September 9, 2012, 07:30	meshing problem	#6
abdul Sami New Member Sami Join Date: Sep 2012 Posts: 15 Rep Power: 13	Hi every One! i want to know that in ansys how i create thick mesh near the boundries(in 2d nozzle) and in the centre it should be thin plz help any one plzz

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Heat transfer (conduction) between two pipes	shields	FLUENT	14	February 3, 2016 07:45
Water subcooled boiling	Attesz	CFX	7	January 5, 2013 03:32
Modelling Heat transfer between stack and gas in Thermoacoustic	Chirag2302	FLUENT	0	April 24, 2012 01:14
need papers on heat transfer	George	Main CFD Forum	0	November 27, 2008 07:42
Modelling combustion and heat transfer	Tudor	FLUENT	4	May 9, 2005 07:02

September 8, 2012, 05:58		#3
zaynah04 Senior Member zaynah K. Join Date: Jun 2012 Location: Mauritius Posts: 138 Rep Power: 13	Dear Ali I have a problem in gambit i define porous_jump, then in fluent it sent an error message: Error: Cannot change po to porous-jump because there is only one adjacent cell thread. i have tried modify in gambit and its still futile. can you please guide me? Thanks zaynah

September 8, 2012, 14:44		#5
zaynah04 Senior Member zaynah K. Join Date: Jun 2012 Location: Mauritius Posts: 138 Rep Power: 13	Dear Ali Its okay... Zaynah