[ICEM] Problem with cfx ERROR #001100279

TallesC · February 7, 2013, 08:56

I'm working on a pipe with knees, and the following issue is being presented in time to run in cfx:

* ERROR # 001100279 has occurred in subroutine ErrAction.
* Message: Floating point exception: Overflow

when creating the mesh in Icem I refined my knees and part of the next pipe, but the rest I leave the pipe with large elements. this would be the possible cause of the error reported above??

diamondx · February 7, 2013, 08:59

i don't think so , if cfx lets you import other format, like fluent msh files, try that ...

TallesC · February 7, 2013, 09:11

but this problem is being informed when I am putting to rotate, there'm thinking that the problem may be the mesh, you know?

diamondx · February 7, 2013, 10:51

i have no experience in CFX... try the cfx section of the forum

Far · February 7, 2013, 11:56

Refinement is 1:2 or 1:3?

TallesC · February 7, 2013, 13:47

the refinement was only using the edit paramt to increase the number of elements, any idea what is causing this problem?

TallesC · February 7, 2013, 15:08

guys, the probem was mesh, problem solve!!!thank you....

Far · February 7, 2013, 15:23

What was the problem?

TallesC · February 7, 2013, 15:29

how i`m thinkimg problem is large elements in the midle of pipe,I refine, its working!!!

February 7, 2013, 08:56	Problem with cfx ERROR #001100279	#1
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 13	I'm working on a pipe with knees, and the following issue is being presented in time to run in cfx: * ERROR # 001100279 has occurred in subroutine ErrAction. * Message: Floating point exception: Overflow when creating the mesh in Icem I refined my knees and part of the next pipe, but the rest I leave the pipe with large elements. this would be the possible cause of the error reported above??

February 7, 2013, 08:59		#2
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	i don't think so , if cfx lets you import other format, like fluent msh files, try that ... __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

February 7, 2013, 10:51		#4
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	i have no experience in CFX... try the cfx section of the forum __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CFX Mesh Deformation problem	Silmaril	CFX	7	October 19, 2010 10:00
CFX Casting problem: Can it be done all in one?	jfasl	CFX	1	September 14, 2010 03:14
cfx mesh problem...	mactech001	ANSYS Meshing & Geometry	0	November 5, 2009 02:19
Fan Modelling Problem in CFX	Jenny	CFX	8	September 11, 2007 13:59
CFX 4.4 installation problem	Pandu Sattvika	CFX	1	December 1, 2001 04:07

February 7, 2013, 09:11		#3
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 13	but this problem is being informed when I am putting to rotate, there'm thinking that the problem may be the mesh, you know?

February 7, 2013, 11:56		#5
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	Refinement is 1:2 or 1:3?

February 7, 2013, 13:47		#6
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 13	the refinement was only using the edit paramt to increase the number of elements, any idea what is causing this problem?

February 7, 2013, 15:08		#7
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 13	guys, the probem was mesh, problem solve!!!thank you....

February 7, 2013, 15:23		#8
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	What was the problem?

February 7, 2013, 15:29		#9
TallesC Senior Member Talles Caio Join Date: Oct 2012 Location: Brazil Posts: 101 Rep Power: 13	how i`m thinkimg problem is large elements in the midle of pipe,I refine, its working!!!