[ICEM] Icem blocking mesh

S73f490 · April 21, 2013, 14:30

Hi, I'm a beginner of Ansys stuff and I've got to study the behavior of a spray for a little project.
The problem is that I'm trying to mesh with blocking method, but I don't know how to build up and edit the blocks to make them follow the geometry.
I hope some pros could help me!

Thanks in advance for any support!

Ps: I did ICEM tutorial on 2d pipe, with the T-shaped blocking..

RodriguezFatz · April 22, 2013, 03:35

Hi,
If you did the tutorial, you already learned how to build blocks and assign edges to the geometry. So what excactly is the problem here?

S73f490 · April 22, 2013, 12:04

I don't know how to split edges..i need to have the thicknesses without blocks and i don't have any ideas i can do it!

sameben · April 23, 2013, 03:15

Are you looking for something similar to this?

http://db.tt/UDux1co9

RodriguezFatz · April 23, 2013, 04:23

Watch these 3 videos: (in my link is 1/3, but you will find 2/3 and 3/3 on youtube).
http://www.youtube.com/watch?v=tYrbScUH9RE

S73f490 · April 23, 2013, 07:40

@sameben:
yeah! that's great..very closer to what i've in mind!
Can you tell me how you did it?

thx!!!

sameben · April 24, 2013, 05:42

Got that done with GridPro! I can send you the blocking structure for that. Can you send me your email?

April 22, 2013, 03:35		#2
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 25	Hi, If you did the tutorial, you already learned how to build blocks and assign edges to the geometry. So what excactly is the problem here? __________________ The skeleton ran out of shampoo in the shower.

April 23, 2013, 04:23		#5
RodriguezFatz Senior Member Philipp Join Date: Jun 2011 Location: Germany Posts: 1,297 Rep Power: 25	Watch these 3 videos: (in my link is 1/3, but you will find 2/3 and 3/3 on youtube). http://www.youtube.com/watch?v=tYrbScUH9RE __________________ The skeleton ran out of shampoo in the shower.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[snappyHexMesh] No layers in a small gap	bobburnquist	OpenFOAM Meshing & Mesh Conversion	6	August 26, 2015 09:38
[ICEM] ICEM Structured Mesh Problem	OMJT	ANSYS Meshing & Geometry	3	March 22, 2013 10:06
problem when converting mesh (made by ICEM) using fluentMeshToFoam	Forrest_Lei	OpenFOAM	11	October 16, 2009 06:28
Boddy fitted Hexcore Mesh in ICEM Cfd	Mitch	CFX	0	December 29, 2008 06:07
ICEM clustering of mesh points and multiple edges	webhaw	CFX	4	July 25, 2007 16:29

April 22, 2013, 12:04		#3
S73f490 New Member Join Date: Apr 2013 Posts: 3 Rep Power: 12	I don't know how to split edges..i need to have the thicknesses without blocks and i don't have any ideas i can do it!

April 23, 2013, 03:15	Hi	#4
sameben Member Sam Join Date: Mar 2009 Posts: 35 Rep Power: 16	Are you looking for something similar to this? http://db.tt/UDux1co9

April 23, 2013, 07:40		#6
S73f490 New Member Join Date: Apr 2013 Posts: 3 Rep Power: 12	@sameben: yeah! that's great..very closer to what i've in mind! Can you tell me how you did it? thx!!!

April 24, 2013, 05:42		#7
sameben Member Sam Join Date: Mar 2009 Posts: 35 Rep Power: 16	Got that done with GridPro! I can send you the blocking structure for that. Can you send me your email?