[ANSYS Meshing] ICEM, y+<1 and VORFN mesh quality problems / FLUENT

aerohead · June 26, 2013, 05:31

Hi all. I'm currently meshing a flow which includes flow around a cylinder (O-grid mesh type here) that has been cut in half. My turbulence models require a y+ of 1 or under and as such have some high aspect-ratio and low quality cells via an unstructured mesh. Nothing too bad.

However, in ICEM, the VORFN blocks contain cells of extremely low quality/high aspect ratio. When importing into FLUENT I get the following "Warning: minimum Orthogonal Quality below 0.01.". I have tried to modify the VORFN blocks and has reduced the problem marginally. However, the cells of low quality are not found in the 'visible' part of the mesh.

Wondering if there is a way round this in ICEM and how much this will affect my results/convergence etc.?

Thanks for any help!

Far · June 26, 2013, 12:18

VROFN blocks are hidden blocks. Do not check them while generating mesh or exporting

aerohead · June 26, 2013, 12:21

Thanks FAR, I have left them unchecked both during quality checks and when generating the unstructured mesh... and when writing to a FLUENT.msh, but the problem persists. Basically, my problem is that I think ICEM is still 'seeing' them even when they aren't checked

Far · June 26, 2013, 12:24

It is not possible

. Did you regenerete mesh after unchecking VORFN block?

aerohead · June 26, 2013, 12:33

Repeatedly. I just opened the file again to check; pre-mesh>recompute (VORFN not checked). Pre-mesh quality>det3x3 (active parts only selected). I then click on the green histogram bars, nothing shows. If I then enable VORFN and click on the same bars the selected cells now show up only in the VORFN domain. I have no idea why?

June 26, 2013, 05:31	ICEM, y+<1 and VORFN mesh quality problems / FLUENT	#1
aerohead New Member Join Date: Mar 2013 Posts: 5 Rep Power: 13	Hi all. I'm currently meshing a flow which includes flow around a cylinder (O-grid mesh type here) that has been cut in half. My turbulence models require a y+ of 1 or under and as such have some high aspect-ratio and low quality cells via an unstructured mesh. Nothing too bad. However, in ICEM, the VORFN blocks contain cells of extremely low quality/high aspect ratio. When importing into FLUENT I get the following "Warning: minimum Orthogonal Quality below 0.01.". I have tried to modify the VORFN blocks and has reduced the problem marginally. However, the cells of low quality are not found in the 'visible' part of the mesh. Wondering if there is a way round this in ICEM and how much this will affect my results/convergence etc.? Thanks for any help!

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ICEM] Deleting VORFN blocks in ICEM CFD	Sai Swaroop	ANSYS Meshing & Geometry	5	October 18, 2011 10:26
HELP: ICEM blocking and vorfn / orfn	guest7777	CFX	4	November 2, 2007 11:28

June 26, 2013, 12:18		#2
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	VROFN blocks are hidden blocks. Do not check them while generating mesh or exporting

June 26, 2013, 12:21		#3
aerohead New Member Join Date: Mar 2013 Posts: 5 Rep Power: 13	Thanks FAR, I have left them unchecked both during quality checks and when generating the unstructured mesh... and when writing to a FLUENT.msh, but the problem persists. Basically, my problem is that I think ICEM is still 'seeing' them even when they aren't checked

June 26, 2013, 12:24		#4
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	It is not possible . Did you regenerete mesh after unchecking VORFN block?

June 26, 2013, 12:33		#5
aerohead New Member Join Date: Mar 2013 Posts: 5 Rep Power: 13	Repeatedly. I just opened the file again to check; pre-mesh>recompute (VORFN not checked). Pre-mesh quality>det3x3 (active parts only selected). I then click on the green histogram bars, nothing shows. If I then enable VORFN and click on the same bars the selected cells now show up only in the VORFN domain. I have no idea why?