How to understand the modeling concept in blade modeler
I am trying to use Ansys bladegen for generatinng the turbomachinary blade. I am not able to get any tutorials to understand the ways to use it. please suggest?
|
I have some material on it. Send email id.
|
|
Bladegen vs Blademodeler
hey guys,
I am pretty confused about both these applications (I mean Bladegen and Blademodeler). Are both of these used for modelling blades? I am trying to obtain 3d models for some blades I have designed. I have information like chord, axial chord, span, stagger, alpha, beta, etc at 3 locations (thats root, mean and tip). But, I am not sure how to proceed with the blade modelling, all I need is the coordinates for root and tip airfoil (or may be mean as well). Is there any way, I can get some tutorials on using bladegen or blademodeler to obtain blade profile by provide the above said parameters (thats chord, axial chord, span, stagger, alpha, beta, etc). Any help or advice would be appreciated. -- Regards Ranpreet B |
Help please
Help me please i can't make flow path around Axial blade and every time Error:confused:
Error: The meridional plane placement is not correct. Context: ansFClientBMBladeDesign::Execute FlowPath1 my mail: haelsheshtawy@gmail.com |
are you using blade modeller?
|
yes i use blade modeler, import point and extrud the blade, and try to make path flow, Plz any help:confused:
|
Every time this error appears, when make flow path
Error: The meridional plane placement is not correct. Context: ansFClientBMBladeDesign::Execute FlowPath1 |
Dear Sijal Ahmed Memon
Please, can you help me? |
Quote:
Do that in turbogrid or design modeller and then use blade editor/blade modeller tool |
I had used design modeler for model the blade, after that I used blade editor to make flow path, Can i send the File to you on your email to check out?
|
1 Attachment(s)
I have airfoil made in design modeler, and i need to make flow path for it.
this figure of my bladehttp://www.cfd-online.com/Forums/att...1&d=1380815954 |
you need hub and shroud surface. After that you need to do some operation, then you will be able to define flow path. You just need few more steps ... :D
|
I'd made hub, shroud, inlet, and exit lines after that defined it in flow path but
Error massage appears |
Quote:
Can you send these materials to my email too? My email id is osmanpekmutlu@gmail.com. Thanks a lot. |
Blade modeler
Hi guys! I am new in the blade modeler and try to design a horizontal axis wind/hydro turbine. I think, designing the blade in blade modeler will be better than BladeGen. I need some documentation about blademodeler. My e-mail is: abdmuratoglu@gmail.com
Regards |
Is it possible to get the material also for me. My e-mail address is: kdadem@gmail.com
Thank you very much Far and Muratoglu. |
|
Send it to me as well, if you dont mind. :D
Thanks in Advance My email address is ranpreetbhatia@gmail.com |
And me :D
m_najafpour@aim.com |
Quote:
|
Dear sir,
Please mail me blade editor and blade modeler help file and tutorials. My id:mistrycs@gmail.com |
3 Attachment(s)
Dear
Blade editor or blade modeler is not a separate from ansys...it is part of it, only change the preference like that: Step 1: goes to ur workbench and then click on menu bar on option of Tools like that Attachment 38384 Step 2a: goes to License Preference and from where go to Geometry option like that Attachment 38385 Step 2b: Simply change preference from designmodeler to Blade modeler through putting 1 or 0 and get Blade Modeler....Blade editor is already present in blade Modeler. Attachment 38386 ok....done |
Dear umairrasheed,
I want to understand how the basic 2D geometry is generated in CFX bladegen in terms to understand the basic input parameters from preliminary design calculations. If you find or have any help file or tutorial please mail me for understanding. Thanking you, |
Dear Chattan
i have also same problem..i am also new here. |
bladegen
Can somebody provide bladegen material to me?
e-mail: shubham2941@gmail.com |
Need material related with blade gen
Dear all,
Please send me materials related with BladeGen or send me the link to get it. aero.senthilkumar@gmail.com aero.senthilkumar@gmail.com Regards, Senthilkumar:) |
Dear all,
I am writting my master's thesis in ansys and it's hard to understand how the flow path in blade editor is created. When i am trying to do this, error message appears: "Error: The meridional plane placement is not correct.". If anyone have materials related to blade editor or bladegen, I would be very gratefull if you could sent it to: gugafix@gmail.com :) :) |
Quote:
ashwani.thakur321@gmail.com also when i click the help section in blade gen an error occurs as, "failed to launch app" and i am directed to windows support page, does anyone khnow how to get help files of blade gen. Thanks |
...and for me: kez@hotmail.it Thanks SOO much! :D
|
|
Please send me tutorials 12317@eng.asu.edu.eg
|
|
Originally Posted by Far View Post
I have some material on it. Send email id. Pls also send me the material, dervondy@gmail.com Thanks, Doddy |
Quote:
my email:abiyjelo@gmail.com |
All times are GMT -4. The time now is 21:42. |