[Workbench] Ansys 15 meshing not working. Please help...

gamemakerh · September 17, 2014, 08:56

Hi. I tried everything but I cant make simple CFD task to mesh...

In ansys workbench I created "Mesh" element (see ling below) (mesh error is just because I canceled project refresh because of the same issue)
https://www.dropbox.com/s/lho43txhm4ngq6t/mesh.JPG?dl=0

Then in mesh editor window after making all named selections and ect I tried to GENERATE MESH. (see link below)

https://www.dropbox.com/s/l72qlhoeuq..._fail.JPG?dl=0

"Ansys Workbench Mesh Status" window show 2 progress bars
"Overall Progress..."
and
"Parallel Meshing..."

After some moments my all RAM memory filling up (32 GB) and nothing hapens.

The "Overall Progress" and "Prarallel Meshing..." bars do nothing. (waited for more than 2 hours).

Please someone can tell what I need to do to get mesh component working ?

amin.z · September 17, 2014, 10:15

hey

I think this happens because your element numbers are too large! (because you're selected "proximity and curvature" and "fine")
turn "use advance size function" off and change "relevance center" to coarse and try again! if it's OK try to editing your mesh step by step!

gamemakerh · September 18, 2014, 05:48

Thanks amin.z Problem solved.

It's embarrassing but I forgot to change mm to m and got ultra dense mesh.

September 17, 2014, 08:56	Ansys 15 meshing not working. Please help...	#1
gamemakerh New Member Join Date: Sep 2014 Posts: 9 Rep Power: 11	Hi. I tried everything but I cant make simple CFD task to mesh... In ansys workbench I created "Mesh" element (see ling below) (mesh error is just because I canceled project refresh because of the same issue) https://www.dropbox.com/s/lho43txhm4ngq6t/mesh.JPG?dl=0 Then in mesh editor window after making all named selections and ect I tried to GENERATE MESH. (see link below) https://www.dropbox.com/s/l72qlhoeuq..._fail.JPG?dl=0 "Ansys Workbench Mesh Status" window show 2 progress bars "Overall Progress..." and "Parallel Meshing..." After some moments my all RAM memory filling up (32 GB) and nothing hapens. The "Overall Progress" and "Prarallel Meshing..." bars do nothing. (waited for more than 2 hours). Please someone can tell what I need to do to get mesh component working ?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ANSYS Meshing] ANSYS Meshing Graphics autohide	Benedikt	ANSYS Meshing & Geometry	7	February 20, 2017 05:26
Using ICEM CFD to repair/edit ANSYS Meshing	Kaaji1359	ANSYS	2	July 30, 2013 10:28
[ICEM] ICEM sizing function >>> Gambit and Ansys meshing	Far	ANSYS Meshing & Geometry	6	March 5, 2013 01:16
ANSYS program has stopped working?	chihoangkt	ANSYS	0	July 16, 2012 16:41
[ANSYS Meshing] Fine meshing in ANSYS Meshing v13	shk12345	ANSYS Meshing & Geometry	1	December 1, 2011 10:41

September 17, 2014, 10:15		#2
amin.z Senior Member Amin Join Date: Oct 2013 Location: Germany Posts: 397 Rep Power: 14	hey I think this happens because your element numbers are too large! (because you're selected "proximity and curvature" and "fine") turn "use advance size function" off and change "relevance center" to coarse and try again! if it's OK try to editing your mesh step by step!

September 18, 2014, 05:48		#3
gamemakerh New Member Join Date: Sep 2014 Posts: 9 Rep Power: 11	Thanks amin.z Problem solved. It's embarrassing but I forgot to change mm to m and got ultra dense mesh.