[ICEM] ICEM-Fluent mesh transfer fault

cturutoglu · November 4, 2016, 08:46

Hi All!

I am trying to solve a problem with fluent and i've done my meshing process on icem cfd. I finished mesh process and after that i've selected my output solver to Ansys Fluent and than i've selected write input settings as in the icem tutorials but when i tried to open fluent a fatal error appears which

"Error: fluent received a fatal signal (segmentation fault)"

Also, i tried to open my .msh file on fluent after icem saving. I mean, i've copied .msh file to desktop and i've opened a new workbench file, in that file i've opened a new fluent and tried to open .msh file but again a fatal error appeared.

Please help about importing icem mesh on fluent.

Thanks.

cturutoglu · November 4, 2016, 08:56

I have also tried to set q new fluent on icem cfd and refresh. When i did this, icem had an error which

"Error: couldn't execute "D:\Ansys" no such file or directory."

I installed my Ansys at disk D but it is in the "Ansys Inc" folder. I wonder if the error is about that? Am I have to install my Ansys in C: ?

cturutoglu · November 7, 2016, 01:58

Any help?

November 4, 2016, 08:46	ICEM-Fluent mesh transfer fault	#1
cturutoglu Member CT Join Date: May 2016 Location: Turkey Posts: 32 Rep Power: 9	Hi All! I am trying to solve a problem with fluent and i've done my meshing process on icem cfd. I finished mesh process and after that i've selected my output solver to Ansys Fluent and than i've selected write input settings as in the icem tutorials but when i tried to open fluent a fatal error appears which "Error: fluent received a fatal signal (segmentation fault)" Also, i tried to open my .msh file on fluent after icem saving. I mean, i've copied .msh file to desktop and i've opened a new workbench file, in that file i've opened a new fluent and tried to open .msh file but again a fatal error appeared. Please help about importing icem mesh on fluent. Thanks.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
decomposePar problem: Cell 0contains face labels out of range	vaina74	OpenFOAM Pre-Processing	37	July 20, 2020 05:38
Moving mesh	Niklas Wikstrom (Wikstrom)	OpenFOAM Running, Solving & CFD	122	June 15, 2014 06:20
[ICEM] Improving mesh orthogonality in ICEM or Fluent	Harshal	ANSYS Meshing & Geometry	0	December 2, 2013 09:04
Transport mesh from ICEM CFD, to Fluent, to Sysnoise	Wieland	FLUENT	2	April 15, 2012 06:28
[ICEM] Unstructure Meshing Around Imported Plot3D Structured Mesh ICEM	kawamatt2	ANSYS Meshing & Geometry	17	December 20, 2011 11:45

November 4, 2016, 08:56		#2
cturutoglu Member CT Join Date: May 2016 Location: Turkey Posts: 32 Rep Power: 9	I have also tried to set q new fluent on icem cfd and refresh. When i did this, icem had an error which "Error: couldn't execute "D:\Ansys" no such file or directory." I installed my Ansys at disk D but it is in the "Ansys Inc" folder. I wonder if the error is about that? Am I have to install my Ansys in C: ?

November 7, 2016, 01:58		#3
cturutoglu Member CT Join Date: May 2016 Location: Turkey Posts: 32 Rep Power: 9	Any help?